Banner TCNM-AD Series Parameter Manual Download Page 67

Page: 67 / 92

Diagnostics

Diagnostics

When enabled, this group allows selection of the desired diagnostic messages and definition of the relative diagnostic

management parameters.

The relative transmission parameters are described in Actions.

The relative data format parameters are described in Format.

For information on Diagnostic Error Messages see Diagnostic Error Conditions.

Enable

If checked, it allows configuring the Diagnostics parameters. Diagnostic error messages (or alarms) can be used to

activate digital outputs when the Activate on any Diagnostic Error parameter is selected and/or they can be sent as

strings when the Diagnostic Message Format parameter is set as a User Defined String.

Conveyor Info

It allows indicating if information about the conveyor status is available or not.

Selections:

Available

Not Available

Conveyor Info Provider

If the Conveyor Info is Available, this parameter allows setting the source providing info about the conveyor status:

Selections:

Input_1

Input_2

Refresh Time

It defines the frequency at which the diagnostic messages are updated. This parameter excludes the network

diagnostics which are updated at a fixed internal frequency.

LED Indication on Network Slave Failure

This parameter has meaning only for a Master scanner since it allows the LEDs to signal a Network Slave Failure.

When enabled, if a Slave Network Failure is detected, the Master scanner Status and Ready LEDs blink simultaneously

and the GOOD LED remains on constantly.

Slave Diagnostics

This parameter has meaning only for a Master scanner since it enables all diagnostic error messages coming from the

ID-NET™ network slaves (through the Master) to the host. If unchecked, slave scanner alarms will be ignored and will

not be sent to the host.

Local Network Failure

If checked, it allows sending an alarm signalling a malfunctioning of the local ID-NET™ network controller,

independent from the scanner role (Master, Slave, Other).

No Phase Timeout

It defines the time interval after which an error code is generated if no reading phase has occurred.
Selections:

Disable

1 sec

5 sec

10 sec

20 sec

1 min

5 min

10 min

20 min

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands