manualshive.com logo in svg

Banner TCNM-AD Series, Parameter Manual

Share
Download
Banner TCNM-AD Series Parameter Manual Download Page 79

References 

77 

References 

 

 

Diagnostic Error Conditions 

 

 

The following tables summarize all Internal Numeric Error Messages generated when working in the network. 

 

Diagnostic Error Messages

 

 

Stand Alone / Master/ MULTIDATA Slave 

 

Family  Diagnostic

 

Error 

Number

 

Meaning

 

AD/EX  [81] 

Motor Failure:

 the motor speed is above or below the internal threshold with 

respect to the programmed Scan Speed. 

SP 

[81] 

DIGITIZER:

 

Motor  Failure

  the  motor  speed  is  above  or  below  the  internal 

threshold with respect to the programmed Scan Speed. 

SP 

[82] 

DIGITIZER:

 

Motor  Life  End

  the  motor  has  surpassed  its  factory  declared 

functional life. 

AD/EX  [83] 

Laser Failure:

 a laser failure has occurred. 

SP 

[83] 

DIGITIZER:

 

Laser Failure

 a laser failure has occurred. 

SP 

[84] 

DIGITIZER:

 

Laser  Life  End

  the  laser  has  surpassed  its  factory  declared 

functional life. 

SP 

[85] 

DIGITIZER:

 

Data  Consistency  Error

  a  checksum  error  has  occurred  on  the 

analog board EEPROM memory. 

SP 

[87] 

DIGITIZER:

 

Communication  Error

  there  is  a  communication  error  between 

the decoder board and the analog board. 

SP 

[89] 

DIGITIZER:

 

Reset

 an unexpected analog board reset has occurred. 

SP 

[91] 

DIGITIZER:

 

Data Write Error

  a  data  write  error  has occurred  to  the  analog 

board EEPROM memory. 

SP 

[93] 

Focus  Displacement

  the  actual  focus  position  doesn't  match  the  Locked 

Position  saved  in  the  scanner  configuration  memory.  This  alarm  is  generated 

when the focus position has exceeded the allowable tolerance. 

AD/EX  [97] 

Oscillating Mirror Failure

 the oscillating mirror has not been recognized. 

SP 

[97] 

OSCILLATING MIRROR:

 

Motor Failure

 the oscillating mirror motor speed is 

above  or  below  the  internal  threshold  with  respect  to  the  programmed 

Frequency. 

SP 

[98] 

OSCILLATING  MIRROR:

 

Motor  Life  End

  the  oscillating  mirror  motor  has 

surpassed its factory declared functional life. 

AD/EX  [99] 

Oscillating Mirror Data Consistency Error

 a checksum error has occurred on 

the oscillating mirror onboard settings.

 

SP 

[99] 

OSCILLATING  MIRROR:  Data  Consistency  Error

  a  checksum  error  has 

occurred on the oscillating mirror onboard settings.

 

SP 

[101] 

OSCILLATING  MIRROR:  Communication  Error 

there  is  a  communication 

error between the decoder board and the oscillating mirror board.

 

SP 

[103] 

OSCILLATING  MIRROR:  Reset 

an  unexpected  oscillating  mirror  board  reset 

has occurred.

 

SP 

[105] 

OSCILLATING MIRROR: Data Write Error 

a data write error has occurred to 

the oscillating mirror board EEPROM memory.

 

SP 

[119] 

Reading  Conditions  Controller:  Communication  Error

  there  is  a 

communication  error  between  the  decoder  board  and  the  Reading  Conditions 

Controller. 

SP 

[121] 

Focus  Controller:  Communication  Error

  there  is  a  communication  error 

between the decoder board and the Focus Controller. 

SP 

[123] 

Temperature Sensor: Communication Error

 there is a communication error 

between the decoder board and the Temperature Sensor. 

SP 

[124] 

High  Temperature  Warning:

  the  internal  temperature  has  reached  the 

maximum  level.  The  scanner  life  and/or  performance  may  be  reduced. 

Continued operation at this level could cause the scanner to fail. 

SP 

[125] 

Laser Temperature Sensor: Communication Error

 there is a communication 

error between the decoder board and the Laser Temperature Sensor. 

SP 

[127] 

Temperature  sensors  Mismatch  Error:

  the  internal  Temperature  Sensors 

values don't match. 

All 

[131] 

/ 

[133] 

Start/Stop Input Failure:

 the start or stop input is not working. 

All 

[132] 

No  Phase  Timeout:

  no  reading  phase  for  more  than  the  programmed  No 

Phase timeout. 

Summary of Contents for TCNM-AD Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands