Banner TCNM-AD Series Parameter Manual Download Page 81

Page: 81 / 92

References

AD/EX [97]

Oscillating Mirror Failure

the oscillating mirror has not been recognized.

[97]

OSCILLATING MIRROR:

Motor Failure

the oscillating mirror motor speed is

above or below the internal threshold with respect to the programmed

Frequency.

AD/EX [99]

Oscillating Mirror Data Consistency Error

a checksum error has occurred

on the oscillating mirror onboard settings.

[99]

OSCILLATING MIRROR: Data Consistency Error

a checksum error has

occurred on the oscillating mirror onboard settings.

[101]

OSCILLATING MIRROR: Communication Error

there is a communication

error between the decoder board and the oscillating mirror board.

[103]

OSCILLATING MIRROR: Reset

an unexpected oscillating mirror board reset

has occurred.

[105]

OSCILLATING MIRROR: Data Write Error

a data write error has occurred to

the oscillating mirror board EEPROM memory.

[119]

Reading Conditions Controller: Communication Error

there is a

communication error between the decoder board and the Reading Conditions

Controller.

[121]

Focus Controller: Communication Error

there is a communication error

between the decoder board and the Focus Controller.

[123]

Temperature Sensor: Communication Error

there is a communication error

between the decoder board and the Temperature Sensor.

All

[151]

Local Network Failure:

a local ID-NET™ network controller error has

occurred.

All

[185]

TCNM-ACBB Backup Module Communication Failure:

there is a

communication error between the scanner and the Backup module inside the

TCNM-ACBB connection box.

All

[187]

Wrong TCNM-ACBB Backup Module Rotary Switch Selection:

one or more

of the selected Backup module Rotary Switch settings inside the TCNM-ACBB

doesn't match the scanner configuration memory.

Some of these error messages may have different meaning according to different conditions.

NOTE 2

All

DIGITIZER, OSCILLATING MIRROR, and FLASH

errors, except for: DIGITIZER Motor

Warning, Focus Displacement, and High Temperature Warning, require that the relative scanner be

reset before the error can be cancelled.

Error Message Conditions

A single error number can indicate different types of failure according to the following conditions:

working in On Line mode with 1 input and Conveyor Info available

working in On Line mode with 1 input and without Conveyor Info available

working in On Line mode with 2 inputs and with Conveyor Info available

working in On Line mode with 2 inputs and without Conveyor Info available

working in Serial On Line mode

In the following description the following expressions are used:
"presence sensor open"

the presence sensor light beam is broken

"presence

sensor

closed"

the presence sensor light beam is continuous

On Line Operating Mode

When working in On Line operating mode the meaning of an error message can change according to the selection of

the On Line Options parameter and to the selection of the Conveyor Info parameter.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands