Banner TCNM-AD Series Parameter Manual Download Page 47

Page: 47 / 92

Data Communication Settings

Auxiliary Serial Port

This group determines the communication through the Auxiliary Serial Port (RS232 only). This port is also available to

MULTIDATA Slave scanners.

Search for TCNM-ACBB Backup Module at Device Startup

If enabled (checked), at startup, the scanner sends a message to recognize the presence of, and communicate with,

the Backup Module. If using the Backup Module, this parameter must be enabled (checked).

NOTE

Disable this parameter if the Backup Module is not used and the Host must not receive data at

startup.

Data TX

If enabled (checked), data from the scanner will be transmitted on the Auxiliary Serial Port.

Heartbeat

This parameter enables/disables transmission of the Heartbeat message used to signal device or system status at

regular intervals. The Heartbeat message is independent from Data Tx and can be enabled even if data is not sent on

the Auxiliary Serial Port (Data Tx - disabled).
Selections:

Disable

the Heartbeat message is not transmitted

Enable Unconditioned

the Heartbeat message is always transmitted, even if
communication is still active

Enable Conditioned

the Heartbeat message is transmitted only when there is no
communication

Pass Through

It enables/disables the Pass Through options.

Heartbeat

The following parameters allow configuring the Heartbeat message for communication through the Auxiliary Port.

The Heartbeat message is used to signal the device's or system's status at regular intervals to the Host. It has the

following format:

Timeout

This parameter defines the amount of time between two message transmissions. If the selected time out expires and

no transmission has occurred, the Heartbeat message will be transmitted.

Heartbeat Header String

This parameter signals the beginning of the Heartbeat message. It can be a string of up to 128 characters.
Selections: characters from

NUL

(00H) to

(7EH)

The Heartbeat Header String should be different from the Heartbeat Terminator String.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands