Banner TCNM-AD Series Parameter Manual Download Page 54

Page: 54 / 92

TCNM-AD/EX/SP Family Software Configuration Parameter Guide

Bus Communication

NOTE

For further information regarding Fieldbus interfacing including downloadable support files, go to the

HMS website at http://www.anybus.com, choose the link to the support page, select the Anybus-

CompactCom product type and then your network type.

Baud Rate

This is a read-only parameter. The modules are set to use the automatic baud rate mechanism where the Fieldbus

Master defines the speed of the connection. After connection, for some Fieldbus types, the actual speed of the Fieldbus

will be displayed in this parameter.
For CC-Link Fieldbus, the Fieldbus Master does not set the network baud rate and therefore this parameter must be

set manually according to the application specific network baud rate.

Max. Exchange Area Size (Input+Output)

This is a read-only parameter. It defines the (fixed) maximum size of the exchange area (total of both Input and

Output Areas) available for messages between the Fieldbus Master and the Fieldbus module.

Selections:

Profibus

152

DeviceNet

152

Ethernet IP

152

CC-Link

254

CANopen

152

Profinet IO

Modbus TCP

152

Master Input Area Size

It defines the size of the message command sent from the Fieldbus module to the Fieldbus Master.

Selections:

Profibus

a value in the range

8 - 144

DeviceNet a value in the range

8 - 144

Ethernet IP a value in the range

8 - 144

* CC-Link a value in the range

2 - 126

CANopen

a value in the range

8 - 144

Profinet IO a value in the range

8 - 56

Modbus

TCP

a value in the range

8 - 144

* For CC-Link Version 1, the Master Input Area Size must be less than or equal to 30.

Master Output Area Size

It defines the size of the message command sent to the Fieldbus module from the Fieldbus Master.

Selections:

Profibus

a value in the range

8 - 144

DeviceNet a value in the range

8 - 144

Ethernet IP a value in the range

8 - 144

* CC-Link a value in the range

2 - 128

CANopen

a value in the range

8 - 144

Profinet IO a value in the range

8 - 56

Modbus

TCP

a value in the range

8 - 144

* For CC-Link Version 1, the Master Output Area Size must be less than or equal to 32.

Summary of Contents for TCNM-AD Series





























































































Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands

Banner TCNM-AD Series, Parameter Manual

Search results

Summary of Contents for TCNM-AD Series

Reviews:

Brands by name

Popular brands