Astor AS63MTB20C2-A Operation Manual Download Page 99

Page: 99 / 276

SRV-63 series AC servo drives Detailed parameter description

-98-

P0.69

Data size

16bit

Data format

DEC

Modbus address

1138,1139

CANopen address

0x2045, 0x00

P0.70

Absolute encoder mode

setting

Setting range

Default

Unit

Available mode

0~1

This parameter is used to modify the operation mode of the multi-turn absolute encoder. When

the matching encoder for the motor is multi-turn absolute encoder, it will be taken as single-turn

encoder by default; when multi-turn function is needed, it is necessary to prepare the spare battery

and set it as the multi-turn modes.

Setting value

Method

[0]

Single circle

Multiple circles

P0.70

Data size

16bit

Data format

DEC

Modbus address

1140,1141

CANopen address

0x2046, 0x00

P0.71*

Absolute encoder

multi-turn zeroing

Setting range

Default

Unit

Available mode

0~1

Clear the multi-turn absolute encoder via this parameter. The multi-turn data of the encoder will

be cleared after this parameter is enabled while the single-turn data will remain unchanged,

however, the absolute position feedback of the system will be cleared.

Note:

When using multi-turn absolute encoder, after machinery installation is done, please clear the

absolute encoder after detecting absolute zero position of the mechanic system at initial power up.

P0.71*

Data size

16bit

Data format

DEC

Modbus address

1142,1143

CANopen address

0x2047, 0x00

6.1.4 Control mode switching

P0.90

Max. speed limit of

control mode switching

Setting range

Default

Unit

Available mode

1~1000

100

r/min

Set the max. running speed during positioning when switching from speed mode or torque mode

to position mode under position/speed, position/torque compound mode.

P0.90

Data size

16bit

Data format

DEC

Modbus address

1180,1181

CANopen address

0x205A, 0x00

P0.91

Positioning reference of

control mode switching

Setting range

Default

Unit

Available mode

-1~2

-1

reference unit P

Set the motor positioning position after control mode switching is done when switching from

speed mode or torque mode to position mode under position/speed, position/torque compound

mode.

Note:

1. After the switching, the reference point of the received position command is the setting value of

Summary of Contents for AS63MTB20C2-A





















































































































































































































































































Search results

Summary of Contents for AS63MTB20C2-A

Reviews:

Related manuals for AS63MTB20C2-A

Brands by name

Popular brands

Astor AS63MTB20C2-A, Operation Manual

Search results

Summary of Contents for AS63MTB20C2-A

Reviews:

Related manuals for AS63MTB20C2-A

Brands by name

Popular brands