Astor AS63MTB20C2-A Operation Manual Download Page 83

Page: 83 / 276

SRV-63 series AC servo drives Detailed parameter description

-82-

Setting value Logic of B phase

CCW

[0]

Non-reverse

A phase

B phase

A phase

B phase

Reverse

A phase

B phase

A phase

B phase

P0.08

Data size

16bit

Data format

DEC

Modbus address

1016,1017

CANopen address

0x2008, 0x00

P0.09

Torque limit mode setting

Setting range

Default

Unit

Available mode

0~6

This parameter is used to set the torque limit mode.

In speed mode, the analog input 3 is set to the torque limit, and:

Setting value

Forward direction

Reverse direction

Analog input 3(0V~10V)

Analog torque command (-10V~0V)

[1]

Max. torque limit 1(P0.10)

Max. torque limit 2(P0.11)

TLC OFF →Max. torque limit 1(P0.10)

TLC ON → Max. torque limit 2(P0.11)

Analog input 3(0V~10V)

Analog torque command (0V~10V)

Analog input 3(0~10V)

Analog torque command (0V~10V)

If analog input 3 is the speed input (non-torque limit), the meaning of the parameter is as below:

Setting value

Forward direction

Reverse direction

Analog torque command (-10V~0V)

[1]

Max. torque limit 1(P0.10)

Max. torque limit 2(P0.11)

TLC OFF → Max. torque limit 1(P0.10)

TLC ON

→ Max. torque limit 2(P0.11)

Analog torque command (0V~10V)

Note:

If P0.09 is 3, the torque switching is not valid instantly and is limited by P4.51 and P4.52,

the detailed information is as the figure below:

P0.10

P0.11

torque

P0.10

Ta[ms]=|P0.11[%]-P0.10[%]|×P4.51[ms/100%]/100

Tb[ms]=|P0.10[%]-P0.11[%]|×P4.52[ms/100%]/100

Summary of Contents for AS63MTB20C2-A





















































































































































































































































































Search results

Summary of Contents for AS63MTB20C2-A

Reviews:

Related manuals for AS63MTB20C2-A

Brands by name

Popular brands

Astor AS63MTB20C2-A, Operation Manual

Search results

Summary of Contents for AS63MTB20C2-A

Reviews:

Related manuals for AS63MTB20C2-A

Brands by name

Popular brands