Astor AS63MTB20C2-A Operation Manual Download Page 128

Page: 128 / 276

SRV-63 series AC servo drives Detailed parameter description

-127-

position feedback pulse and position command pulse is in this range, it indicates position arrival.

P3.50

Data size

32bit

Data format

DEC

Modbus address

1700,1701

CANopen address

0x2332,0x00

P3.51

Output mode of position

arrival

Setting range

Default

Unit

Available mode

0~4

This parameter can be used to set the condition for the position arrival output signal and the

action mode after output.

Setting value

Output mode

[0]

Output is valid if the position deviation is within the range of P3.50.

Output is valid when there is no position command and the position deviation

is within the range of P3.50.

Output is valid when when there is no position command, the zero speed

detection signal is valid and position deviation is within the range of P3.50.

Output is valid when transiting from the position command to no position

command and the position deviation is within the range of P3.50. And then,

valid state of output continues until passing the time set by P3.52, after that,

updates the position arrival output state according to the position command

and the position deviation.

Output is valid when transiting from position command to no position

command while position deviation is within P3.50. Thereafter, the valid state

of output continues until passing the set time by P3.52.

P3.51

Data size

16bit

Data format

DEC

Modbus address

1702,1703

CANopen address

0x2333,0x00

P3.52

Hold time of position arrival

output terminal

Setting range

Default

Unit

Available mode

0~30000

This parameter is used to set the hold time of position arrival output terminal.

Setting value

Action

[0]

Hold time is infinite, continuous valid state to the next position command position

1~30000

Valid only within the setting value [ms]. If position command is received during

hold time, it will change to invalid state immediately.

P3.52

Data size

16bit

Data format

DEC

Modbus address

1704,1705

CANopen address

0x2334,0x00

P3.53

Speed matching range

Setting range

Default

Unit

Available mode

10~20000

r/min

This parameter is used to set the detection condition of speed matching output.

If the difference between the speed command and the motor speed is below the setting value,

then the output state of the speed matching is valid.

The threshold of the speed matching when there is 10r/min lag:

Speed matching output: Invalid

→ Valid threshold: (P3.53 – 10)r/min

Summary of Contents for AS63MTB20C2-A





















































































































































































































































































Search results

Summary of Contents for AS63MTB20C2-A

Reviews:

Related manuals for AS63MTB20C2-A

Brands by name

Popular brands

Astor AS63MTB20C2-A, Operation Manual

Search results

Summary of Contents for AS63MTB20C2-A

Reviews:

Related manuals for AS63MTB20C2-A

Brands by name

Popular brands