manualshive.com logo in svg

Altigen MAX Communication Server ACC 6.5, Administration Manual

Share
Download
Altigen MAX Communication Server ACC 6.5 Administration Manual Download Page 454

440

MAXCS ACC 6.5 Administration Manual

Table 1.

Signaling values, by country

Country

Signaling Values

Chile/Nacional MFC-
R2

Set calling part category

: 1

[Assume no caller ID provided]: 

Incoming sequence

: DID/DNIS

In-call signaling

 (depend on how many DID digits): 

For 3-digit DID, set to (113)6
For 4-digit DID, set to (1113)6
For 5-digit DID, set to (11113)6
For 6-digit DID, set to (111113)6
For 7-digit DID, set to (1111113)6
For 8-digit DID, set to (11111113)6
[Assume caller ID provided]: 

Incoming sequence

 (same as above shown): DID/

DNIS  *  Caller ID

In-call signaling

 (depend on how many DID digits): 

For 3-digit DID, set to (115)*(K)36
For 4-digit DID, set to (1115)*(K)36
For 5-digit DID, set to (11115)*(K)36
For 6-digit DID, set to (111115)*(K)36
For 7-digit DID, set to (1111115)*(K)36
For 8-digit DID, set to (11111115)*(K)36

Summary of Contents for MAX Communication Server ACC 6.5









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands