Home
/
Altigen
/
MAX Communication Server ACC 6.5
/
Administration Manual

Altigen MAX Communication Server ACC 6.5, Administration Manual

Share

Page: 343 / 488

Altigen MAX Communication Server ACC 6.5 Administration Manual Download Page 343

Chapter 25: Enterprise VoIP Network Management

MAXCS ACC 6.5 Administration Manual 329

Click a tab to view or configure settings on that tab. Information on a tab is related to
the selected server. Click buttons in the toolbar to perform configuration tasks. Click a

column heading to sort by that column.

Configuration Buttons

•

Servers

button displays the VoIP domain name, servers in the system, and server

ID length. Lets you add/remove servers and change the VoIP domain master. Lets

you re-route outgoing calls of global extensions and redirect AltiGen IP phones.
Displays the configuration and informational tabs listed in the next section.

•

Codec

button lets you configure individual codec profiles—silence suppression,

codec, jitter buffer range, RTP packet length, DTMF delivery, enable/disable SIP
early media, and SIP transport.

•

User

button displays information about extensions in the VoIP domain and lets you

change an extension to global or local and relocate an extension.

•

Department

button lets you define departments in the VoIP domain and assign

extensions to departments.

•

Global LCR

button lets you add E.164 number patterns and specify source and

target sites.

Tabs Displayed with the

Servers

Button

•

Information

tab displays information about the selected site and lets you configure

a PSTN number for global extension rerouting as a failover when the TCP/IP network
is down. You may also assign an alternate server to which to redirect global AltiGen

IP phones when their primary server is down.

•

IP Networks

tab defines IP networks and the bandwidth information for an MAXCS

site. Bandwidth usage control for Internet and intranet can be set up here. If the
bandwidth usage exceeds the maximum setting, the call will not be established.

•

IP Dialing Table

tab defines the IP dialing table for an MAXCS site. Specified

information here includes a codec profile and a protocol (SIP or H323) for the
communication from this site to the selected site.

•

IP Codec

tab lets you specify an inter-gateway codec and define IP device ranges

to which you can assign a codec profile.

•

Number Plan

tab displays the number plan information that is set up in MaxAdmin,

System Configuration window,

Number Plan

tab.

Changing the Enterprise Manager Password

Only a person with DomainAdmin rights can change the Enterprise Manager password.
To change the password, click the

Password

button at the top of the Enterprise

Manager window. The following dialog box opens:

«
...
341
342
343
344
345
...
»

Summary of Contents for MAX Communication Server ACC 6.5









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands