Home
/
Altigen
/
MAX Communication Server ACC 6.5
/
Administration Manual

Altigen MAX Communication Server ACC 6.5, Administration Manual

Share

Page: 148 / 488

Altigen MAX Communication Server ACC 6.5 Administration Manual Download Page 148

Chapter 11: Board Configuration

134

MAXCS ACC 6.5 Administration Manual

Setting the ISDN PRI Switch Mode

If you select a Span Type of Regular ISDN PRI in the T1 PRI Configuration Window, use

the following guidelines to set the ISDN PRI Switch mode.

Figure 13. T1 PRI Switch Mode

The top four settings are used for a connection to a CO switch:

•

AT&T 4ESS PRI

•

AT&T 5ESS PRI

•

NT DMS-100 PRI

•

NI-2 PRI (default)

The bottom four settings are used for a PRI tie trunk configuration where two MAXCS

systems are connected back to back. In such a configuration, one MAXCS system must
be configured as Network and the other as User. For example, set one to NI-2 PRI
Network and the other to NI-2 PRI.

•

AT&T 4ESS PRI Network

•

AT&T 5ESS PRI Network

•

NT DMS-100 PRI Network

•

NI-2 PRI Network

«
...
146
147
148
149
150
...
»

Summary of Contents for MAX Communication Server ACC 6.5









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands