manualshive.com logo in svg

Altigen MAX Communication Server ACC 6.5, Administration Manual

Share
Download
Altigen MAX Communication Server ACC 6.5 Administration Manual Download Page 387

Chapter 26:  Redundancy Configuration

MAXCS ACC 6.5 Administration Manual 373

Figure 5. Monitoring the status and configuring the addresses of VM server and Enterprise 

server

When the Address of the Softswitch Server Changes

Configure the new address on the VM server and the Enterprise server.

VM Server

If the address of the Softswitch is changed, you need to configure the new address on 
the VM server so that the VM server can connect to the correct softswitch. Do this using 

the Voice Message Server Utility. Run ...\AltiServ \exe\VMMonitor.exe to launch the 
utility, shown in the following figure.

Summary of Contents for MAX Communication Server ACC 6.5









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands