manualshive.com logo in svg

Altigen MAX Communication Server ACC 6.5, Administration Manual

Share
Download
Altigen MAX Communication Server ACC 6.5 Administration Manual Download Page 191

MAXCS ACC 6.5 Administration Manual 177

C

H A P T E R

13

In Call Routing Configuration

In Call Routing rules determine how the system routes incoming trunk calls to various 
targets. The system’s routing steps are as follows:

The In Call Routing Configuration window lets you enter Caller ID and DNIS numbers into 

a routing table and set routing rules for a matched number. 
To configure In Call Routing, select 

PBX > In Call Routing Configuration

.

Step

Routing Process

1

Match DID number configured in extension, workgroup, or hunt 
group. If there is no match, go to the next step.

2

Match caller ID defined in the Caller ID Routing table. If there is a 
match and

•

today is a holiday, route the call according to the Holiday Profile’s 
routing rules.

•

today is 

not

 a holiday, route the call according to business hour 

routing rules defined in the Caller ID Routing configuration.

If there is no caller ID match, go to the next step.

3

Match DNIS number defined in the DNIS Routing table. If there is a 
match and

•

today is a holiday, route the call according to the Holiday Profile’s 
routing rules.

•

today is 

not

 a holiday, route the call according to business hour 

routing rules defined in the DNIS Routing configuration.

If there is no DNIS number match, go to the next step.

4

If today is a holiday, route the call according to the Holiday Profile 
configured for the trunk port that the call is coming in on. If today 
is 

not

 a holiday, route the call according to the business hours 

routing rules defined in the 

In Call Routing

 tab of the Trunk 

Configuration window.

Summary of Contents for MAX Communication Server ACC 6.5









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands