Home
/
Altigen
/
MAX Communication Server ACC 6.5
/
Administration Manual

Altigen MAX Communication Server ACC 6.5, Administration Manual

Share

Page: 349 / 488

Altigen MAX Communication Server ACC 6.5 Administration Manual Download Page 349

Chapter 25: Enterprise VoIP Network Management

MAXCS ACC 6.5 Administration Manual 335

The SIP transport assigned to an extension in the IP Phone Configuration screen takes
precedence over a codec profile with a different SIP transport assigned in Enterprise

Manager. If the IP extension supports TLS and the codec profile does not, then the IP
extension policy holds. That way you can configure a range of IP addresses in the IP
dialing table or IP codec, and have only a few IP addresses/extensions support TLS.
If the IP extension has not configured TLS as its transport, and the codec profile supports

it, then the codec profile policy holds.
To set IP address ranges and assign codec profiles to them, in Enterprise Manager click
the

IP Codec

tab.

By default, all private addresses are set to G.711 codec only. You can add individual IP

addresses and address ranges and assign a codec to each.

To add IP addresses and address ranges and assign a codec

1. Click the

Add

button in the IP Device Range panel. The Add IP Device Range dialog

box opens:

«
...
347
348
349
350
351
...
»

Summary of Contents for MAX Communication Server ACC 6.5









































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands