Altigen MAX Communication Server ACC 6.5 Administration Manual Download Page 249

Page: 249 / 488

MAXCS ACC 6.5 Administration Manual 235

H A P T E R

AltiGen IP Phone Configuration

AltiGen manufactures a series of IP phones. The system administrator can control and
program the following areas for each type of AltiGen IP phone:

•

Specify the server IP address that the IP phone needs to register

•

Protect the IP phone configuration with a password

•

Prevent the user from changing the configuration from the IP phone

•

Configure the Trunk Access (Route Access) code

•

Configure the time zone and time format

•

Specify the TFTP server for firmware updates

•

Force the IP phone to reset and download new firmware

•

Set SIP transport settings for SIP security

•

Enable SIP telephony service for a selected third-party SIP device

•

Configure programmable keys

•

Allow the IP phone to receive workgroup real time status

•

Allow the phone to auto-discover the server’s IP address

To configure the AltiGen IP phone, select

PBX > AltiGen IP Phone Configuration

Summary of Contents for MAX Communication Server ACC 6.5









































































































































































































































































































































































































































































































Search results

Summary of Contents for MAX Communication Server ACC 6.5

Reviews:

Brands by name

Popular brands

Altigen MAX Communication Server ACC 6.5, Administration Manual

Search results

Summary of Contents for MAX Communication Server ACC 6.5

Reviews:

Brands by name

Popular brands