Zontes ZT310T-M Скачать руководство пользователя страница 87

Страница: 87 / 184

184

troubleshooting.

c. "SEAT" button failure
If the battery is out of power and inconvenient to charge, or the cushion lock fails to open, you can fill in the quality

feedback form and let the engineer guide the method of manually opening the cushion. For safety reasons, this
manual does not provide this method.

The cushion

can't open

Whether the

battery has

electricity

Can the fuel tank

cap be opened?

Charge the

battery

Check PKE (brown-

yellow and blue-red

control terminals)

Does the horn

sound

Submit the quality

feedback sheet to be

solved by the engineer

Sub switch

failure

d. “ ”Not responding
There is a detailed description of PKE functions in the driver's manual, including the method of emergency starting

the vehicle when the sensor key is exhausted, and the specific meaning of the buzzer sound.

No response

when

unlocking

The sensor key is

too far away

Whether the

sensor key has

sufficient power

Bring the

induction key

close to

Replace the battery, the

model is CR1225

Disassemble the right

auxiliary switch and

short-circuit the

unlocking switch wire

Right auxiliary

switch failure

Fill in the quality

feedback form and

assist in the

investigation by

the engineer

4.3Left hand handle auxiliary switch

Left hand

handle

Auxiliary

switch

Left hand handle

Auxiliary switch

failure

No response when

pressing MOD

Remove the auxiliary

switch and short the

button switch line

No response when

pressing SET

Troubleshoot

cable or

instrument failures

The windshield

cannot be raised

or lowered by

pressing the

windshield button

Whether it is normal

to push or pull the

windshield rocker

arm by hand

Check the

windshield motor

or motor controller

4.4 Horn
Caution:

●There should be more than 5 seconds interval when adjusting or checking the horn. Continuous sounding may cause

ablation of the internal coil of the horn.

●The horn is a riveted structure, w

hich is difficult to restore after disassembly.

Содержание ZT310T-M

























































































































































































Результаты поиска

Содержание ZT310T-M

Отзывы:

Похожие инструкции для ZT310T-M

Бренды по названию

Популярные бренды

Zontes ZT310T-M, Руководство по обслуживанию

Результаты поиска

Содержание ZT310T-M

Отзывы:

Похожие инструкции для ZT310T-M

Бренды по названию

Популярные бренды