Zontes ZT310T-M Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 184

background image

133

/

184

8. Braking system

Know Before Service

1. The content of this chapter requires certain maintenance experience. It is recommended to check or repair with a
qualified maintenance organization.
2. Frequent inhalation of the dust generated by the brake pads, regardless of the composition, may have a certain
impact on health. Avoid breathing dust particles.
3. Do not use a blow gun or brush to clean the brake assembly, but a vacuum cleaner.
4. Avoid dripping the brake fluid on the paint surface of the cover or the surface of the parts. If it is accidentally
splashed, it needs to be rinsed with water immediately.
5. When disassembling the front disc brake main pump and the rear disc brake main pump, make sure that the brake
fluid in the oil cup is in a horizontal position. Do not turn it upside down to prevent air from entering, which will affect
the braking effect. In severe cases, it may cause the brake to fail and cause personal injury.
6. The steps for replacing brake fluid and exhausting air are the same. For detailed steps, see the section on brake
fluid in the "Maintenance" chapter.
7. When the brake pads or brake discs have oil stains, the braking force will be reduced. The contaminated brake
pads should be replaced, and the oil stains on the brake discs can be removed with a good-quality degreasing
cleaner.
8. After removing the oil cup cover of the main pump, prevent dust and water from entering.
9. If you need to add brake fluid after maintaining the brake system, you must use the newly opened DOT4 brake fluid.
Do not mix with other brake fluids.
10. Switch to unplug the ABS hydraulic control unit when the vehicle is powered on. Excessive voltage may damage
the hydraulic control unit. The entire vehicle must be powered off before maintenance.
11. The hydraulic control unit is a precision part, and it is forbidden to disassemble it by non-professionals.

●If you ac

cidentally swallow the brake fluid, you should contact the poison control center or hospital immediately; if

you accidentally get the brake fluid into your eyes, rinse with water and seek medical attention immediately.

●Brake fluid must be kept away from c

hildren and pets.

●The vehicle must be parked on a flat and stable ground or a lifting platform.

●Wear protective gloves/protective clothing/protective goggles/protective masks to maintain the brake system.

●It is strictly forb

idden to directly flush the main pump with high-pressure water.

«
...
131
132
133
134
135
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: R&G Страницы: 22

Бренд: R&G Страницы: 8

Бренд: GIVI Страницы: 3

Бренд: Honda Страницы: 243

Easyrack 6612533 01 01

Бренд: hepco & becker Страницы: 5

Бренд: R&G Страницы: 27

HPS.08.473.10000/B

Бренд: SW-Motech Страницы: 4

Бренд: Öhlins Страницы: 2

Бренд: Aim Страницы: 5

Бренд: Hama Страницы: 22

Бренд: SUR-RON Страницы: 37

Бренд: JAWA Страницы: 22

Бренд: SILENCE Страницы: 68

Бренд: HYOSUNG Страницы: 100

Бренд: HYOSUNG Страницы: 96

RST MILLE FUTURA - PART 2 2000

Бренд: APRILIA Страницы: 50

Бренд: KTM Страницы: 7

Бренд: Honda Страницы: 189

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды