manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT310T-M Скачать руководство пользователя страница 119

 

 

119

 / 

184

 

 

6. Fuel supply system 

Know Before Service 

1. Bending or twisting the control cable will affect the smooth operation, and may cause a short circuit or open circuit, 
causing the vehicle to lose control. 
2. The operation should be carried out in an open and ventilated place. All activities that may cause sparks, such as 
smoking, calling on mobile phones, etc., are prohibited on the job site. 
3. Before operation, release the pressure of the high-pressure fuel pipe. The method is as follows: unplug the fuel 
pump, start the engine and run at idling speed until the engine stops. Turn off the engine

，

Turn off to "

", turn off the 

power and lock the bike. 
4. Do not fully open the throttle valve body manually after removing the throttle cable, which may cause abnormal 
idling. 
5. After removing the throttle valve body, apply masking paper or a clean non-woven fabric to block the air inlet to 
prevent foreign matter from falling into the engine. 
6. Do not damage or operate the throttle valve body, which may cause abnormal throttle operation. 
7. After removing the throttle valve body, prevent dust or foreign matter from entering the throttle hole or air passage. 
If necessary, it can be cleaned with dry compressed air. 
8. It is forbidden to loosen or tighten the bolts or nuts that have been marked with a marker on the throttle, which may 
cause abnormal throttle opening and closing and idle speed control. 
9. Cannot use carburetor cleaning agent. 
10. Throttle valve body parts not specified in this manual shall not be disassembled. 

 

●After r

einstalling the battery or EFI components, reset the EFI system. For specific operations, please refer to the 

precautions in the driver's manual or the throttle valve body chapter of this manual. 
 

Fuel tank removal 

Caution:

 

●The

 demolition site must be ventilated and pay 

attention to fire prevention. See the previous chapters 
for specific matters, so I won’t repeat them here. 

●First use the oil well pump or wait until the fuel in the 

fuel tank is almost exhausted before disassembling. 

●Be careful not to pull the nylon rope shown in the 

figure, forcibly pulling it may break. And our company 
does not sell this nylon rope separately. 

 

●Pay attention to protect the oil outlet of the oil pump, 

and only pull out the high-pressure oil pipe axially. Be 
careful not to pull or press the oil port radially. 

 

1. Disassemble the fuel tank assembly 

a. Follow the steps in the pre-service instructions to 

first consume the fuel in the high-pressure fuel pipe. 

b. Refer to the steps for removing the cover first to 

remove the outer cover of the fuel tank, the side cover, 
the pedal and other plastic appearance parts. Use a 4# 
inner hexagon to remove the bolt 

⑵

  at the water pipe 

bracket, and then use a 10# sleeve to remove the 2 
bolts 

⑴

  that fix the pedal on the right side. 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды