manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT310T-M Скачать руководство пользователя страница 164

 

 

164

 / 

184

 

 

   

3. Put the coolant and pull out the 

connection plug 

a. Place suitable utensils under the big arrow, use 

water clamp pliers to remove the green hoop pointed by 
the big arrow, pull out the engine water inlet pipe, and let 
out the coolant; then use a single batch to remove the 
clamp pointed by the small arrow and pull it out The inlet 
pipe of the small water tank discharges the coolant. 

   

b. Unplug the high-voltage package plug from the 

engine head. 

   

c. Refer to the steps in "Remove the Throttle Valve 

Body Assembly to Clean Carbon Deposits" and unplug 
the plugs of the stepping motor 

①

  and the three-in-one 

sensor 

②

  on the throttle valve body. 

   

d. Locate and unplug the plugs of the high-pressure 

fuel pipe 

③

  and the fuel injector 

④

  at the front end of 

the throttle valve.   

Caution:

 A small amount of fuel will flow out when the 

high-pressure oil pipe is pulled out, and it is forbidden to 
drip onto the surface of the part. 

   

e. Locate and unplug the crankshaft position sensor 

⑤

  and the oxygen sensor 

⑥

  in the frame position on 

the right.   

Caution:

 One end of the crankshaft position sensor is 

connected to the inside of the engine, one end is 
connected to the main cable; one end of the oxygen 
sensor is connected to the engine in front of the muffler, 
and the other end is connected to the main cable; do not 
unplug the wrong plug. 

   

f. Locate and pull out the plug of the magneto stator 

charging cable 

⑦

  at the left frame. 

 

Caution:

 One end of the magneto stator charging cable 

is connected to the inside of the engine, and one end is 
connected to the connector on the rectifier; do not pull 
out the wrong plug. 

   

g. Use an 8# sleeve to remove a bolt on the starter 

motor, and take out the negative wire 

⑧

  on the bolt. 

Caution:

 The negative wire of the early production 

model is fixed on the bolt around the starter motor. 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды