Zontes ZT310T-M Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 184

background image

136

/

184

1- Caliper mounting plate 2- Brake pad holder 3- Caliper
pin rubber cap 4- Piston 5-dust seal 6-oil seal 7-caliper
pin 8-bleed nozzle 9-bleed nozzle rubber cap 10-caliper
housing 11-caliper mounting plate pin rubber cap 12-
brake spring

Caution:

●Apply silicone grease to the surfaces of the two pins

indicated by the arrows.

●The oil seal and dust seal should be replaced with new

ones after disassembly. DOT4 brake fluid should be
applied to the oil seal and piston, and silicon grease
should be applied to the outer ring of the dust seal.

●Apply thread fastening glue to the thread of the caliper

pin, torque: 22N.m (2.2kgf.m, 16 lbf.ft).

●The torque of the air release nozzle: 7

～

9N.m (0.7

～

0.9kgf.m, 5

～

7 lbf.ft).

●The open end of the piston should face the caliper

mounting plate, and do not install it backwards.

●If there is slight rust on the surface of the piston, it can

be polished off with 2000 mesh fine sandpaper.

e. Refer to the disassembly procedure to restore all

parts and add new DOT4 brake fluid according to the
procedure of replacing the front disc brake brake fluid.
Only after confirming that the brake is restored can the
vehicle be driven.

Disassemble the rear disc brake caliper

a. Place an oil pan at the bottom of the caliper, wear

waterproof gloves and loosen the bolt

⑴

with a 12#

sleeve, remove the copper pad

⑵

, and remove the RC-

HU oil pipe. Refer to the steps for adding brake fluid to
the main pump of the rear disc brake. Remove the
upper cover of the main pump to accelerate the
discharge of the brake fluid. Bolt

⑴

Standard torque:

32N.m (3.3kgf.m, 24 lbf.ft).

b. Use a 14# sleeve to remove the bolt (3). Standard

torque of bolt (3): 24N.m (2.4kgf.m, 18 lbf.ft).

c. Refer to the procedure for replacing the brake pads

to remove the brake pads first.

d. Disassemble the rear disc brake caliper
Refer to the previous steps to disassemble the front

disc brake caliper piston to remove the rear disc brake
caliper piston. Check the piston and caliper cylinder for
scratches, damage, pits, etc. Check whether the pin is
deformed. The points that should be paid attention to
during cleaning and assembly are detailed in the
previous description, and will not be repeated here.

1- caliper mounting plate pin 2- bushing 3- rubber cap 4-
caliper pin 5- vent nozzle 6-vent nozzle rubber cap 7-oil
seal 8-dust seal 9-piston 10-caliper pin rubber cap 11-
Caliper mounting plate 12- Brake pad spring 13- Caliper
housing

Caution:

●Apply silicone grease to the surface of the pin and

bush indicated by the arrow.

●The oil seal and dust seal should be replaced with new

ones after disassembly. DOT4 brake fluid should be
applied to the oil seal and piston, and silicon grease
should be applied to the outer ring of the dust seal.

«
...
134
135
136
137
138
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: yasuni Страницы: 8

Бренд: R&G Страницы: 8

Power Commander III 718-411

Бренд: Dynojet Страницы: 3

Бренд: GAS GAS Страницы: 119

Бренд: GAS GAS Страницы: 32

Бренд: yasuni Страницы: 12

Бренд: X-lite Страницы: 96

TXT PRO - PART LIST 2005

Бренд: GAS GAS Страницы: 38

Бренд: Ericsson Страницы: 44

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 2

Бренд: AGUSTA Страницы: 427

Бренд: Engelbert Strauss Страницы: 46

MADISON 300 2018

Бренд: Malaguti Страницы: 120

Бренд: APRILIA Страницы: 151

Бренд: hepco & becker Страницы: 3

Бренд: Petzl Страницы: 3

Бренд: Petzl Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды