Zontes ZT310T-M Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 184

background image

130

/

184

foreign objects on the surface.

2. Attention to the water tank filling port:

●Special ventilation tooling (gas pressure reducing valve, air gun, sealing tube) is

required for testing.

●After the soaking inspection is completed, the water stains

should be wiped clean in

time.

2.1 Overall leak check

Seal the small tube and ventilate the large tube for air tightness inspection.

2.2 Check of pressure relief valve

Pass 120kPa (1.22 Kgf/cm2, 17.4 psi) compressed air into the big pipe, put the water

filler into the water and let stand for 10 seconds. The small pipe should be free of
bubbles. Increase the compressed air to

130kPa (1.33 Kgf/cm2, 18.9 psi). Bubbles

appear.

3. Auxiliary water tank

First check whether the rubber cover is aging and cracked, if any, replace it. If the

appearance is good, then check the air tightness.

Seal the two small water outlets and open the black plastic cover of the water tank for

air tightness inspection.

Continue to seal the small water outlet, fill the auxiliary tank with water and turn the

auxiliary tank upside down, and observe whether the rubber cover of the water tank
seeps. If there is seepage, it is unqualified. Pour out the water after checking the
tightness, remove the plug and let the auxiliary water tank dry naturally or blow it dry
with a dust blower.

4. Aluminum inlet pipe and aluminum outlet pipe

Check whether the weld is cracked or cracked; check whether the buffer rubber is

aging and cracked. If the appearance is good, then check the air tightness.

Seal one end and ventilate from the other end to check air tightness.

5. Small water tank

Check whether the fan and net cover are firmly assembled, and there should be no jamming of the rotating fan

blades. Check whether the cushion rubber is aging and cracked. Check whether the fan cable is damaged.

Seal one water outlet and ventilate from the other end for air tightness inspection.
The blue of the fan plug is the positive pole, and the black is the negative pole. Find a battery with sufficient power

and connect the wires according to the positive and negative poles, and check whether the fan draws air backwards.

Compressed air with lower air pressure can be blown from the back to the water tank from a long distance to clean

up foreign objects on the surface. Or use a low-pressure water gun to spray the radiating fins from a long distance to
clean up foreign objects on the surface.

«
...
128
129
130
131
132
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 9

2016 Empulse TT

Бренд: Victory Motorcycles Страницы: 138

Easyrack 661658 01 01

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: RIEJU Страницы: 72

Бренд: Benelli Страницы: 51

Бренд: APRILIA Страницы: 227

250 EXC-F AUS 2012

Бренд: KTM Страницы: 18

Бренд: KTM Страницы: 12

Бренд: KTM Страницы: 12

Бренд: KTM Страницы: 7

2013 1190 Adventure R

Бренд: KTM Страницы: 213

Бренд: Harbor Freight Tools Страницы: 9

Бренд: Royal Enfield Страницы: 104

Bullet Electra 350 2006

Бренд: Royal Enfield Страницы: 69

Бренд: AFX Страницы: 92

Бренд: Xmotos Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды