Zontes ZT310T-M Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 184

background image

162

/

184

11. Disassemble the engine of the vehicle

Caution:

●The vehicle must be parked on a level and stable

ground or on a lifting platform.

●The operation can only be performed after the engine

has cooled down completely.

●Do not press the brake handle after removing the rear

brake caliper.

●Attention and sequence when removing the plastic

buckle to avoid the buckle from breaking

●Wear waterproof gloves when draining coolant to

prevent it from getting on your skin.

●The storage box of subsequent production models has

been changed. For disassembly and assembly, please
refer to the chapter "Disassembly of the storage box" in
"Disassembly of Vehicle Covers".

1. Disassemble the storage box

a. Push the whole car to a wide, flat place, lay down

the main bracket, and unlock the cushion lock.

b. Use 4# inner hexagon and other tools to remove

the 2 expansion nails on the battery cover, remove the
battery cover, and then use 4# inner hexagon to remove
the 2 expansion nails connected to the storage box on
the middle cover of the fuel tank (green mark).

c.Use 4# hex socket to remove the two M6×16 bolts

⑴

next to the battery, take out the bushing

⑵

, the

buffer rubber

⑶

, take out the battery negative rubber

sleeve at the arrow, use a cross-shaped batch to
remove the battery negative electrode, and then take out
the battery positive glue Remove the positive and
negative poles of the battery using a cross-shaped
screwdriver. After removing the positive and negative

wires of the battery, screw the bolts on the battery back
with a cross-shaped screwdriver.

d. Take out all the relays and fuse boxes next to the

battery.

e. Remove the decorative glue at the back of the

storage box, and then take out the decorative buckle on
the bolts, use 4# inner hexagon to remove the 2 M6×16
bolts that fix the storage box (1), take out the bushing
(2), cushion rubber (3).

f. Lift the glove box slightly until the ambient light

connector is exposed on the left side of the glove box,
unplug the connector and take out the entire glove box.

«
...
160
161
162
163
164
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: Keis Страницы: 2

STEADYSTAND Cross Basic

Бренд: ACEBIKES Страницы: 6

COMFORT 10130810

Бренд: Contracor Страницы: 36

Бренд: GAS GAS Страницы: 119

Бренд: R&G Страницы: 9

Scout 25L Pannier Kit V2.0

Бренд: MOSKO MOTO Страницы: 13

Бренд: GAS GAS Страницы: 150

Бренд: BMW Страницы: 16

Бренд: zeeltronic Страницы: 10

Freeride 350 2013

Бренд: KTM Страницы: 113

Battery Relocation Kit

Бренд: BoxerCafe Страницы: 7

Бренд: Suzuki Страницы: 165

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 114

YZF-R1P 2001-2003

Бренд: Yamaha Страницы: 439

Бренд: National Cycle Страницы: 2

Бренд: PMI Страницы: 2

Бренд: DYNATEK Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды