Zontes ZT310T-M Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 184

background image

84

/

184

d. Check the battery voltage
Open the cushion, take off the battery cover and use a

multimeter to measure the battery voltage. If it is lower
than 12V, you should use the charger provided with the
car to charge it in time. Be careful not to overcharge and
over discharge, and the charging voltage of the charger
must not be higher than 15V. When the car is not used
for a long time, it should be charged regularly in
accordance with the requirements of the driver's manual.
If the battery fails, it should be properly handled by a
professional recycling agency, and do not discard it at
will to avoid environmental pollution.

or

If the battery power supply fails to start, it can be

charged through the PKE charging port.

Open the right storage box cover, insert the buckle

with your fingernail or a thin flat-blade screwdriver, press
inward and pull out the buckles on both sides, and then
remove the right storage box cover.

Open the protective cap

①

, pull out the PKE

insurance

③

, first insert the DC output plug of the

charger provided with the car into the PKE charging
port; then connect the charger input AC terminal to 110-
220V household AC.

①

is the protective cap for the charging DC interface;

②

is the charging insurance;

③

is the PKE insurance,

which must be unplugged when charging the battery
through the DC interface with the charger;

④

is the

TEST button, which function is same as the unlock
button on the auxiliary switch.

2. Headlight height adjustment
Caution:

●The height of the headlights is too high or too low,

which will affect safe driving. The light height should be
adjusted reasonably according to the presence or
absence of the occupant and the weight change of the
driver.

●It is strictly forbidden to adjust the light height during

riding. It is recommended to find a smooth road with a
straight line distance of about 150 meters for adjustment
under the premise of not affecting traffic safety at night.

Use a polished rod with a diameter of 6mm (0.24 in)

and a length of 150

～

200mm (6

～

8 in) with a Phillips

screwdriver from just below the headlights and go up
through the dimming hole of the horn bracket, and align
it with the serration of the dimming bolt; Rotate the
clockwise to turn down, and counterclockwise to turn up.

«
...
82
83
84
85
86
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: Dakota Digital Страницы: 6

Бренд: R&G Страницы: 26

Бренд: N-Com Страницы: 2

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 102

Бренд: DYNATEK Страницы: 4

Бренд: Arai Helmet Страницы: 28

COMP-MLCS-12200

Бренд: Compcooler Страницы: 11

Бренд: SHERCO Страницы: 54

gtrack 7855 MyBASIC

Бренд: Gemini Страницы: 20

Бренд: Shark Страницы: 24

Бренд: Enerwatt Страницы: 26

MADISON 300 2018

Бренд: Malaguti Страницы: 120

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 162

Бренд: Yamaha Страницы: 251

Бренд: Petzl Страницы: 14

RST MILLE FUTURA - PART 2 2000

Бренд: APRILIA Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды