Zontes ZT310T-M Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 184

background image

63

/

184

g. Pull out the rear caliper assembly and check the

wear of the brake pads. If it is nearly worn or worn to the
limit position, new brake pads must be replaced in pairs.

●A qualified maintenance organization should check and

maintain the brake pads on a regular basis.

●Do not drive immediately after replacing a new brake

disc or brake pad. Be sure to hold and release the brake
handle several times to allow the brake disc and brake
pads to fully fit together to restore normal grip and to
make the brake fluid circulate stably.

●The braking distance may be longer than the original

braking distance after replacing the new brake disc or
brake pad. It needs to be used for about 300 kilometers
(186 mile). Good braking effect. Allow enough braking
distance before running in sufficiently to ensure driving
safety.

●The brake pads must be replaced in pairs, only

replacing one side will cause uneven braking.

●If th

e position of the brake pads is incorrect, it is

forbidden to operate the brake handle. Otherwise, it will
be difficult to reset the piston and may cause brake fluid
leakage.

2. Check the front and rear brake switches

2.1 Check the brake switch

Hold the brake handles of the main pumps of the front

and rear disc brakes respectively, and observe whether
the rear brake lights are on. If it does not light, you need
to investigate: whether the brake switch is faulty;
whether the rear brake light is faulty; whether the fuse
has blown; whether the circuit is open.

2.2 Replace the brake switch

Take the replacement of the rear brake switch as an

example to explain.

a. Pull out the two plugs of the brake switch in the

direction of the arrow without distinguishing the positive
and negative poles.

b. Use a Phillips screwdriver to remove the bolt

①

to

remove the rear brake switch

⑴

.

c. Replace with a new switch, pay attention to align

the switch boss and the limit hole of the brake main
pump.

The replacement procedure of the front brake switch

is the same as that of the rear brake switch. The throttle
cable needs to be removed to facilitate the removal of
the bolt

①

.

3. Lubricate the movable parts of the brake handle

3.1 Lubricate the front brake handle.

a. Use a 10# torx wrench to rotate counterclockwise to

remove the nut

③

.

b. After grasping the handle, use a 5# inner hexagon

counterclockwise rotation to remove the bolt

①

; remove

the brake handle.

c. Wipe the handle pusher and the outer end of the

piston with a clean non-woven cloth (the position shown
in Figure

②

), and apply high vacuum silicone grease

Front brake switch

Rear brake switch

«
...
61
62
63
64
65
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: Yamaha Страницы: 88

Бренд: R&G Страницы: 9

Бренд: Miller Страницы: 12

Бренд: Honda Страницы: 243

Бренд: hepco & becker Страницы: 4

SUPERSPORT1000 2003

Бренд: Ducati Страницы: 328

Superbike 749R 2006

Бренд: Ducati Страницы: 608

Бренд: hepco & becker Страницы: 6

Бренд: Surtek Страницы: 12

Бренд: hepco & becker Страницы: 2

Road Sofa H18-07-18X all

Бренд: Saddlemen Страницы: 2

Бренд: Power Fist Страницы: 4

Бренд: Malaguti Страницы: 121

Бренд: RIEJU Страницы: 39

Бренд: RIEJU Страницы: 51

Бренд: Vetter Страницы: 18

Бренд: KTM Страницы: 240

Бренд: HYOSUNG Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды