Zontes ZT310T-M Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 184

background image

64

/

184

evenly.

d. Wipe clean the bolt

①

, and apply high vacuum

silicone grease evenly.

e. Reinstall.

3.2 After lubricating the brake handle

Refer to the above method to lubricate the rear brake

handle.

3.3 Replacing the brake handle

Refer to the previous steps to remove the nut

③

and

bolt

①

to replace the new brake handle.

4. Adjust the brake handle

In order to adapt to more drivers driving this model, it

is equipped with an adjustable brake handle. Take the
right front brake handle as an example. Push the end of
the handle to the end in the direction of the arrow, and
adjust the wheel clockwise by hand. The extension of
the push head will increase the distance between the
handle and the rubber sleeve, and vice versa. The
adjustment method of the rear brake handle on the left is
opposite to that on the right.

5. Replace the brake pads

●A qualified

maintenance organization should check and

maintain the brake pads on a regular basis.

●Do not drive immediately after replacing the new brake

pads. Be sure to hold and release the brake handle
several times to allow the brake disc and brake pads to
fully fit together to restore normal grip and to make the
brake fluid circulate stably.

●The braking distance may be longer than the original

braking distance after replacing the new brake pads. It
needs to be used for about 300 kilometers (186 mile), and
the best braking effect can be achieved after the brake

disc and the brake pads are fully run-in. . Allow enough
braking distance before running in sufficiently to ensure
driving safety.

●The brake pads must be replaced in pairs, only

replacing one side will cause uneven braking.

●The brake pads must be assembled correctly.

●Do not operate the brake handle after removing the

brake pads.

5.1 Update the front brake pads

a. Use a flat-blade screwdriver to remove the nut

①

.

Remove the pin shaft

②

with a 5# inner hexagon.

b. Remove the brake pads.
c. Push the piston to the end in the direction of the

arrow with the help of a tool. If the resistance is high,
you can refer to the method of adding brake fluid to the
front brake main pump to remove the upper cover and
then push. If the spring on the caliper falls off, it needs to
be reinstalled in the direction shown in the figure.

d. Take out the new brake pad and install it back. You

need to hold the bottom of the brake pad (through hole
end) with your hand. Be careful not to install it
backwards, the side with 3 grooves faces the brake disc;
the black metal back plate faces the caliper.

e. Observe from both sides whether the upper part of

the brake pad has hit the shrapnel, otherwise the
position needs to be readjusted.

outside

inside

«
...
62
63
64
65
66
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: Idaho Страницы: 72

Бренд: UNIT 1 Страницы: 23

Бренд: Kabuto Страницы: 16

Бренд: GAS GAS Страницы: 142

Бренд: rizoma Страницы: 10

Бренд: hepco & becker Страницы: 4

Бренд: Corbin Страницы: 4

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 114

YZF-R1P 2001-2003

Бренд: Yamaha Страницы: 439

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 118

ACCESORIES 2005

Бренд: Triumph Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды