Zontes ZT310T-M Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 184

background image

66

/

184

6. Replace the brake disc

●The vehicle must be parked on a flat and stable ground or a lifting platform.

●After repla

cing the brake discs, brake pads, or reassembling the front and rear wheels, the brake handle must be

operated repeatedly until the brakes restore the braking effect.

●Contaminated disc brake discs and disc brake pads will reduce the braking effect. Please

replace with new disc brake

discs and clean the contaminated brake discs.

●After disassembling the brake disc or rim assembly, please do not operate the brake handle.

●Check the new brake disc for run out ≤0.08mm (0.003 in) before assembling.

6.1 Replacing the front brake disc

The front brake disc can be removed by referring to

the description of the steps for disassembling the front
wheel assembly in the "Front Fork Assembly" of this
manual.

6.2 Replacing the rear brake disc

a. Use 6# inner hexagon to tighten the exhaust port

nut

⑴

; use a 14# sleeve to remove the bolts

⑵

on the

position of 3 of connecting the muffler and the rear
rocker arm. Note that the muffler must be completely
cooled before it can be operated.

b. One person pinches the rear brake handle, and one

person uses 21# impact wrench to remove the
rear wheel nut (3). Standard torque of nut (3): 125N.m
(12.8 kgf.m, 92 lbf.ft).

c. Use 4# hex socket to remove the bolt

⑸

on the

right middle of the rear inner mudguard, remove the
bushing

⑹

and cushion rubber

⑺

, use 4# hex socket

to remove the front bolt

⑷

and the rear bolt

⑸

.

Remove the two bolts

⑷

at the bottom of the rear

rocker arm, and remove the wheel speed sensor

⑻

.

Pull out the staples on the position indicated by the
arrow and remove the decorative cover

⑼

of the

engine right cover.

d. In the gap between the left air filter and the rear

inner mud board, hold the air filter housing with one
hand, and press the rear inner mud board at the position
2 indicated by the arrows with the other hand. Separate
the rear inner mud plate from the staples on the air filter
and lift it up to facilitate subsequent removal of the rear
rocker arm.

e. Use a 14# sleeve to remove the 2 bolts

⑿

that fix

the rear brake caliper, and tie the caliper and the wheel
speed sensor cable. Pay attention to let the calipers sag
naturally without affecting the rocker arm after
disassembly. Use a 14# sleeve to loosen the 2 bolts

⑽

.

«
...
64
65
66
67
68
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Бренд: 3M Страницы: 84

Бренд: Kabuto Страницы: 12

Бренд: Suzuki Страницы: 206

Бренд: Parweld Страницы: 4

Бренд: KTM Страницы: 90

Бренд: hepco & becker Страницы: 2

Бренд: Fantic Motor Страницы: 60

TMAX ABS Series

Бренд: Yamaha Страницы: 122

Tenere 700 2024

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 509

Бренд: Yamaha Страницы: 508

Бренд: Yamaha Страницы: 510

Бренд: Yamaha Страницы: 578

Бренд: Yamaha Страницы: 610

Бренд: Yamaha Страницы: 610

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды