manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT310T-M Скачать руководство пользователя страница 174

 

 

174

 / 

184

 

 

of the small arrow; pull out the two mushroom buttons 
(blue circles) on the front cover After exiting; continue to 
grasp the mark on the front cover (green rectangle) and 
pull it diagonally upward according to the big arrow until 
the 6 buckles on both sides of the front cover (yellow 
area, 3 on the left and right) are all pulled out. 

 

c. After pulling out all the buckles, grasp the mark on 

the front cover (green rectangle) with your hand, and 
pull it down in the direction of the arrow until the front 
cover is removed. 
 

 

Removal of the front panel 

a. Use 4# inner hexagon to remove the two M6×12 

bolts 

⑷

  on the front panel. 

 

b. Grasp the mark on the front front cover (green box) 

with your hands, and pull out according to the arrow 
until the mushroom head (blue circle) on the right side of 
the front front cover is pulled out; use the same method 
to remove it The mushroom head on the left side of the 
front front cover. 

 

c. Grasp the mark on the front cover (green rectangle) 

with your hands, and pull it up in the direction of the 
arrow until the two positioning buckles (blue circles) of 
the front front cover and both sides of the front front 
cover are fixed. (Yellow area, 6 locations on the left and 
right), pull out the 12 buckles, and remove the front 
cover. 

 

Disassembly of headlights 

a. Use the 5# inner hexagon to remove the 4 non-

standard M6×16 bolts 

⑸

  around the headlight (red 

circle), remove the bushing 

⑵

  and the cushion rubber 

⑶

; use a cross to remove the 2 fixed headlight self-

tapping Nail 

⑹

. 

 

b. Hold the headlight with one hand and take it out for 

a certain distance, pull out the 3P plug (green and white 
wire) behind the headlight with the other hand, and take 
out the headlight completely. 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды