manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT310T-M Скачать руководство пользователя страница 86

 

 

86

 / 

184

 

 

①

 

start up  Protection starting circuit 

10A 

②

 

ABS 

Protect the ABS controller 

10A 

③

 

Assistant 

Protect position lights, turn signals, tail lights, brake lights, 
license plate lights, horns, overtaking lights and other lamps 

10A 

④

 

Others 

Protect the deputy handle switch, Speedometer, windshield, 
anti-theft device connector 

10A 

 

There are two 10A spare fuses on the outside of the fuse box. 

4. Troubleshooting 

If the button cannot be pressed, it is directly judged as a switch problem. If there is no response when pressed, it is 

necessary to judge the problem of the switch, circuit, or electrical device. 

4.1 Right hand switch 

a.No response when pressing the start button

：

 

No response 

when pressing 

the start button

Is the key 

nearby

Y

Whether the 

battery has 

electricity

N

Bring the key 

close

N

Charge the 

battery through 

the PKE 

charging port

Y

Whether the 

insurance is 

blown

Whether the 

electric torch 

light is on

N

Disassemble the 

handle switch and 

short-circuit the start 

button switch line

Y

The right hand 

handle vice 

switch failure

Y

Whether the 

flameout switch 

is on

N

Troubleshoot 

the main cable

N

Disassemble the 

handle switch and 

short-circuit the 

switch line of the 

flameout switch 

button, can it be 

started?

Y

N

Faulty right handle 

switch

Turn to

“

     

”

Y

N

Y

 

b. When the light switch is turned on, the headlight does not turn on, check whether the light fuse is blown, if it is 

blown, check the cable fault; if it is normal, disconnect the handle switch and short the light switch line, if it is lit, it is 
judged as a switch failure. Otherwise, check for cable or headlight failures. 

c. The "E"/"S" mode cannot be switched by pressing the ECO button. Disconnect the switch and short the ECO 

button switch line. If it is lit, it is judged as a switch failure. If it is not lit, check the meter and cable failure. 

4.2 Right hand handle vice switch 

a.“FUEL”Button failure 

Short press 

"FUEL" no 

response

Whether the 

battery has 

electricity

Charge the 

battery

N

Disassemble the 

auxiliary switch and 

short the "FUEL" 

switch wire

Sub switch 

failure

Y

Y

N

Refer to the troubleshooting 

process of the fuel tank cap not 

opening

 

b. No response at start-up 
If the engine cannot be started, please refer to the previous "No response when pressing the start button" for 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды