Zontes ZT310T-M Скачать руководство пользователя страница 165

Страница: 165 / 184

165

184

h. Use an 8# sleeve to remove a bolt on the starter

motor, and take out the negative wire

⑧

on the bolt.

Caution:

The negative wire of the early production

model is fixed on the bolt around the starter motor.

i. Locate and unplug the plug of the cylinder head

water temperature sensor

⑩

on the right side of the

throttle valve body.

Caution:

The water temperature sensor of the cylinder

head is directly connected to the engine, do not pull out
the wrong way.

j. Locate and unplug the tube connecting the throttle

body to the carbon canister at the lower part of the
throttle body.

k. Locate and unplug the pipe connecting the oil and

gas separator to the air filter on the left side of the
throttle body.

l. Use a 4# inner hexagon to remove one M6×12 bolt

⑸

that fixes the wheel speed sensor on the rear rocker

arm, take out the wheel speed sensor and take it out of
the fixed clamp. Then use a 14# sleeve to remove the
two M8×37 bolts

⑹

that fix the brake caliper, and pass

the brake caliper and wheel speed sensor in the
direction of the arrow from the middle of the shock
absorber.

4. Disassemble the engine

a. Use a 12# sleeve to remove the two M8×25 bolts

⑺

that fix the right pedal bracket, and remove the rear

right pedal.

b. One person uses a 17# torx wrench to insert a M12

nut

⑼

that fixes the engine on the left side of the

vehicle from the front of the air filter, and another person
uses a 15# sleeve to remove a M12×1.25×290 bolt that
fixes the engine on the right side of the vehicle

⑻

, pull

out the bolt from the frame.

Содержание ZT310T-M

























































































































































































Результаты поиска

Содержание ZT310T-M

Отзывы:

Похожие инструкции для ZT310T-M

Бренды по названию

Популярные бренды

Zontes ZT310T-M, Руководство по обслуживанию

Результаты поиска

Содержание ZT310T-M

Отзывы:

Похожие инструкции для ZT310T-M

Бренды по названию

Популярные бренды