Zontes ZT310T-M Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 184

background image

159

/

184

(5.1 kgf.m, 37 lbf.ft). If one of the shock absorbers is not
installed in place, the front axle will not be tightened or
can not be inserted into the right shock absorber. You
need to remove the shock absorber that is not in place
and install it in place.

d. After installing the front wheel, use the 6# inner

hexagon to tighten the two M8×35 bolts at the bottom of
the right front shock absorber, torque: 20N.m (2.0 kgf.m,
15 lbf.ft).

e. First use a single batch to separate the two brake

pads inside the brake caliper. If the resistance is too
large and the two brake pads cannot be separated,
please refer to the method of "Adding Brake Fluid" to
remove the upper cover of the disc brake oil cup and
then separate it. 2 brake pads, align the gap between
the 2 brake pads in the disc brake caliper with the brake
disc on the front wheel and install it. Then use a 14#
sleeve to tighten two M8×37 bolts (2), torque: 24N.m
(2.5 kgf.m, 18 lbf.ft).

f. Press the position held when the front mud plate is

removed, pass through the appropriate position in the
middle of the shock absorber, and install it to the
corresponding position, use the 4# inner hexagon to
reinstall the 2 M6×12 bolts (3), do not miss the
installation of the lining Set

⑷

, and cushion rubber

⑸

.

Then use the 5# inner hexagon to reinstall the two
M6×30 bolts

⑴

,

Caution:

the left M6×30 bolt

⑴

needs

to have a spring washer

⑹

.

●The vehicle must be

parked on a level and stable

ground or on a lifting platform.

●After the front wheel is installed, please press the

brake handle repeatedly until the brake restores the
braking effect.

Replace the lower link board

Caution:

●After the front wheel is disas

sembled, please do not

press the brake handle.

●When the disc brake oil cup is removed, it must be

vertically upward to prevent air from entering the brake
pipeline.

●After disassembly, make sure that all parts are

installed correctly.

●Appropriate amount

of grease should be applied when

installing the bearing

1. Disassemble parts ahead of time

Refer to "Replace the front wheel", "Replace the front

shock absorber", "Replace the steering handle", and
remove the front wheel, front shock absorber, and
direction handle.

2. Remove the faucet lock

a. Turn on the vehicle, press the 2 front storage box

switches at

①

to open the left and right storage boxes.

b. Use 4# inner hexagon to remove 6 M6×16 bolts

⑴

,

among which 4 M6×16 bolts above the storage box are
covered with bushings

⑵

, cushion rubber

⑶

; then use

4# inner hexagon or other tools to remove The two
expansion nails on the lower storage box

⑷

, take out

the left and right storage boxes, the left storage box has
a line connection, do not pull it vigorously, just place the
foot pedal.

c. Extend the 10# torx wrench from the gap in the

storage box, remove the two M6×20 bolts on the faucet

lock support

⑸

, remove the faucet lock and faucet lock

support, no need to connect the faucet lock and the

faucet Remove the lock and put it in a suitable place

next to it.

«
...
157
158
159
160
161
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: Yamaha Страницы: 860

Бренд: hepco & becker Страницы: 6

Бренд: hepco & becker Страницы: 6

Бренд: oset Страницы: 20

Бренд: Ohlins Страницы: 4

Бренд: Honda Страницы: 102

COMP-MLCS-12200

Бренд: Compcooler Страницы: 11

Бренд: TM Страницы: 80

Бренд: RS Motorcycle Solutions Страницы: 2

Бренд: Montesa Страницы: 114

4Ride MST260 2016

Бренд: Montesa Страницы: 158

VENTURA BIKE-PACK SYSTEM Series

Бренд: DOLD Страницы: 4

Бренд: BMW Motorrad Страницы: 28

Бренд: BMW Motorrad Страницы: 170

Lectra VR24 1998

Бренд: EMB Страницы: 58

Бренд: Engelbert Strauss Страницы: 46

MADISON 3 125 cc

Бренд: Malaguti Страницы: 38

Бренд: Petzl Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды