Zontes ZT310T-M Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 184

background image

178

/

184

Disassembly of the foot pedals and

trim cover

a. Protrude the rear pedal rubber pad and rear pedal

rubber pad pressure plate from the position indicated by
the small arrow with the Slot-type Screwdrivers. Pull the
rear pedal rubber pad and rear pedal rubber pad
pressure plate upward in the direction of the big arrow
until the rear pedal rubber pad and rear pedal rubber
pad pressure plate are removed.

Caution:

Use a tool

such as non-woven cloth to wrap the Slot-type
Screwdrivers when using it to prevent scratches on the
paint surface.

b. Remove 5 non-standard M6x16 bolts

⑸

on the left

pedal with 5# inner hexagon, and remove bushing

⑵

and

buffer glue

⑶

.

Caution:

one of them is only with bushing,

without buffer glue.

c. Remove the two M6x16 bolts

⑴

of the left pedal

decorative cover with 4# inner hexagon and take out the
bushing

⑵

and buffer glue

⑶

.

d. Remove an M6x16 bolt

⑴

from the bottom plate

and the decorative cover of the left pedal with a 4# inner
hexagon, and remove the bushing

⑵

and buffer glue

⑶

;

then remove the 1 nail of the left pedal decorative cover
and 2 nails of the bottom plate

e. Hold the left pedal decorative cover and the left

pedal with two hands and take out the left pedal
decorative cover and the left pedal in the direction of the
arrow.

f. Remove the right pedal trim cover and the right

pedal in the same way.

Removal of the surrounding middle

part

Use 4# inner hexagon to remove the two M6×12 bolts

⑷

connecting surround middle part and the front

«
...
176
177
178
179
180
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: Dakota Digital Страницы: 38

750 Sport Bevel Heaven

Бренд: Ducati Страницы: 235

Бренд: APRILIA Страницы: 9

Бренд: Honda Страницы: 28

Бренд: Baja motorsports Страницы: 20

Бренд: TRS Страницы: 38

Бренд: Toolland Страницы: 25

Бренд: National Cycle Страницы: 2

Бренд: DYNATEK Страницы: 4

Бренд: Yamaha Страницы: 9

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 91

Бренд: Yamaha Страницы: 92

Virago XV250 2004

Бренд: Yamaha Страницы: 95

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды