Zontes ZT310T-M Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 184

background image

169

/

184

6.4 Installing the side cover

a. Put down the right rear pedal, buckle the 5

mushroom buckles (green markings) on the side cover
into the vehicle from front to back (arrow direction),
check the assembly clearance and install 1 M6×16 bolt

⑴

At the tail of the tail skirt, use 4# inner hexagon to

tighten, pay attention to the bolt with bushing

⑵

,

cushion rubber

⑶

. Finally, close the right rear pedal.

b. Use the same method to install the left side cover.

6.5 Armrest after installation

a. Align the rear armrest with the mounting hole on the

frame and install it, and then install 2 M6×12 bolts

⑸

, 5

M8×25 bolts

⑿

, and tighten them with 4# inner hexagon

and 12# sleeves respectively. , Buckle the decorative
glue above the bolts; finally install 2 expansion nails in
the middle of the rear armrest (the green mark).

6.6 Install the device box

a. Arrange the wiring harnesses and connectors of the

relay, fuse box, etc. under the seat cushion, align the
front of the storage box with the installation position and
install it, so that the rear of the storage box is
suspended; find the storage box atmosphere light
connector and main wiring harness on the left side of the
vehicle Connect the connector on the upper side; then
assemble the rear of the storage box in place. When
installing the rear of the storage box, pay attention to the

position of the middle cover of the fuel tank to prevent
the storage box from crushing the middle cover of the
fuel tank.

b. Remove the 2 bolts on the battery using a cross-

shaped screw, first install the battery positive wire (red),
use the cross-shaped screw to install the battery
removed bolts to fix the positive wire, and buckle the
positive rubber sleeve; use the same Install the negative
wire and buckle the negative rubber sleeve. When the
negative wire is connected to the battery, the buzzer will
emit a beep; turn on the vehicle and ignite, check
whether the car is normal, and continue to assemble if
there is no abnormality. If there is a malfunction, check
and reinstall until the car can be started normally.

c. Tighten the two M6×16 bolts (1) at the front of the

storage box with 4# inner hex. Note that the bolts must
be equipped with bushings (2) and cushion rubber (3);
then connect the middle cover of the fuel tank to the
storage box (green mark) Place) Use 2 expansion nails
to fix; tighten the 2 M6×16 bolts at the rear of the
storage box (1) with 4# inner hexagon. Note that the
bolts need to be equipped with bushings (2), cushioning
glue (3), and finally buckle with decorative glue.

d. After finishing the wiring harness, fuse box and

«
...
167
168
169
170
171
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

Бренд: CB Sabbiatrici Страницы: 43

Бренд: Big Bike Parts Страницы: 2

Бренд: X-lite Страницы: 136

Бренд: Ohlins Страницы: 4

Бренд: Caberg Страницы: 16

Бренд: R&G Страницы: 4

Бренд: Wedze Страницы: 63

Бренд: Miller Страницы: 12

Бренд: YCF Страницы: 78

Бренд: Kabuto Страницы: 19

R 1200 R Classic

Бренд: BMW Страницы: 1

Бренд: Husqvarna Страницы: 12

Бренд: Husqvarna Страницы: 12

Бренд: Husqvarna Страницы: 7

Бренд: Husqvarna Страницы: 32

Бренд: Husqvarna Страницы: 7

Бренд: Husqvarna Страницы: 128

Бренд: Tipperary Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды