manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT310T-M Скачать руководство пользователя страница 138

 

 

138

 / 

184

 

 

with tape to prevent the residual brake fluid from 
dripping on the parts when the oil pipe nut joint is 
loosened. Use a 12# open-end wrench to loosen the oil 
pipe nut joints at the hydraulic control unit 
counterclockwise. The nut torque: 18N.m (1.8 kgf.m, 13 
lbf.ft). Wipe up the remaining brake fluid with a clean 
non-woven fabric. Take care to take protective 
measures and prevent dripping onto the cover or cable 
connector. 

FMC-HU and RMC-HU 

Use an 8# sleeve to remove the bolt 

⑴

  that fixes the 

seat of the oil pipe, pull down the upper part of the FMC-
HU hose, pull it out from the lower part of the direction 
cover, and then pull it out from the hose bracket. Check 
whether the surface of the removed hose is aging, 
cracked, damaged, abraded, etc. Wipe up the remaining 
brake fluid with a non-woven cloth, and then wrap the 
ends of the hose with cling film or a plastic bag to 
prevent foreign matter from entering. 

Remove and inspect the RMC-HU hose in the same 

way. 

 

FC-HU and wheel speed sensor (front wheel) 

 

a. Locate the plug of the wheel speed sensor on the 

left side of the frame, and pull out the plug after pressing 
the anti-release card. 

b. For the removal method of FC-HU and wheel 

speed sensor caliper, please refer to the section 
“Removing the front disc brake caliper”. 

c. Cut off the 2 cable ties 

⑴

, remove the 3 wire ties 

⑺

, and remove the wheel speed sensor wire 

⑹

. Check 

whether the cable is damaged. If the cable sheath is 
frayed, wrap it with electrical tape to avoid short-circuit 

and cause vehicle failure. The front wheel speed sensor 
is also responsible for providing a speed signal to the 
meter to display the speed per hour. 

Use an 8# sleeve to remove the bolt 

⑵

, and take off 

the FC-HU hose. 

If you need to remove the hose bracket 

⑷

, you can 

use 4# inner hexagon to remove the bolt 

⑶

  and then 

take it off. If you only remove the hose, you can skip this 
step. 

 

d. Check whether the surface of the removed hose is 

aging, cracked, damaged, abraded, etc. Wipe up the 
remaining brake fluid with a non-woven cloth, and then 
wrap the ends of the hose with cling film or a plastic bag 
to prevent foreign matter from entering. Check whether 
the cable sheath of the wheel speed sensor cable is 
damaged. If the sheath is frayed, it can be glued with 
electrical tape to prevent short-circuit. 

RC-HU and wheel speed sensor (rear wheel) 

a. Find 3 cable ties on the frame tube above the fuel 

tank on the right side of the frame, and cut the cable ties 

⑴

  that bind the RC-HU hose in the middle. Do not cut 

the other 2 cables. When reinstalling, make sure that 
the cable tie cannot be tied too tightly, and a certain gap 
should be left. 

 

b. Find the plug of the wheel speed sensor 

⑵

  on the 

right side of the middle part and unplug it. 

 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды