Zontes ZT310T-M Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 184

background image

158

/

184

Replacement of the front shock

absorber

Caution:

●After the front wheel is disassembled, please do not

press the brake handle.

●Be careful not to damage the ABS coil when

disassembling.

●When disassembling the front

fender, be careful not to

scratch the shock absorber or the front fender.

●When removing the shock absorber, first remove the 2

bolts that fix the same shock absorber, remove one side
of the shock absorber, and then remove the other side.

1. Disassemble the front wheel and front fender

assembly

a. Refer to "Replace the front wheel" to remove the

front wheel.

b.Use 5# inner hexagon to remove one M6×30 bolt

⑴

, and take out the pipe clamp. Then use a 14# sleeve

to remove two M8×37 bolts (2), and remove the front
brake caliper.

c.Use 4# inner hexagon to remove the two M6×12

bolts on the left and right sides of the front fender

⑶

,

remove the 2 bushings

⑷

, cushion rubber

⑸

; then use

5# inner hexagon to remove one M6×30 bolt

⑴

, take

out the gasket

⑹

.

d.First press the two sides of the front mud board

according to the small arrow, press the protrusion on the
front mud board arrow inward, and then move the front
mud board up to a suitable position and then pull it out in
the direction of the big arrow.

2. Remove the left and right front shock absorbers

a.Use a 14# sleeve to remove the 4 M10×1.5×43 bolts

⑺

, pry open the gap on the lower link plate with a

straight batch, and remove the front left shock absorber
and the front right shock absorber.

3. Reinstall the shock absorber, front fender, front

wheel and other components

a.Pry a gap on the lower connecting plate with a flat-

headed batch, insert the corresponding shock absorber,
install the shock-absorbing in place, take the next batch,
screw in two M10×1.5×43 bolts

⑺

, use a 14# sleeve

Tighten two M10×1.5×43 bolts

⑺

, torque: 55N.m (5.6

kgf.m, 41 lbf.ft)

b. Use the same method to install another shock

absorber.

c. Pick up the front wheel and install the bushing, align

the mounting holes between the two shock absorbers,
penetrate the front wheel axle, and tighten the front
wheel axle with a 17# inner hexagon. Torque: 50N.m

«
...
156
157
158
159
160
...
»

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

GearTronic ZERO GT3100-K1

Бренд: PZRacing Страницы: 2

Бренд: Touratech Страницы: 4

Бренд: Honda Страницы: 140

Бренд: hepco & becker Страницы: 2

Бренд: TVS Страницы: 60

Бренд: Baja motorsports Страницы: 66

Бренд: Abus Страницы: 18

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 96

X-MAX 400 ABS 2018

Бренд: Yamaha Страницы: 118

Virago XV250T 2004

Бренд: Yamaha Страницы: 95

Бренд: Yamaha Страницы: 103

Бренд: Yamaha Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды