Xylem sensus AutoRead Скачать руководство пользователя страница 43

Страница: 43 / 161

•

Retry on Bad Read

: May be enabled if directed by Sensus Technical Services to

improve MXU response in situations where RadioRead success is intermittent. Allows

the VXU to attempt interrogation multiple times prior to signaling the Bad Read message.

Altering this without consent from Technical Services may actually hinder system

performance.

•

Export Readings

: The available selections for this setting are Last and All. If

Last

selected, only the last meter reading for any single meter is sent back to the billing

software. This is the most common setting, and will provide the billing software with only

one meter reading (the last one) for any meter. If

All

is selected, all the meter readings for

any given meter are sent back to billing.

All

should not be selected unless you are certain

that more than one reading for a meter is desired by the billing software.

•

User Name

: A User Name can be entered for the specific VXU device. This User Name

will appear on the AutoRead reports and is not currently used for any other purpose.

•

Band

: This setting changes the radio transmit band that the VXU uses for meter

readings. The choices are A, B, and C. A is the US Band, B is the Canadian Band,

and C is the US Alternate Band. You should not change the band setting without

first consulting Sensus Technical Services at 1-800-638-3748, or their Sensus Sales

Representative. Changing the VXU band is a violation of your FCC license and may

cause your system to not operate properly.

•

Channel

: This setting changes the transmit channel that the VXU uses for meter

readings. Consult Sensus Technical Services at 1-800-638-3748 or your Sensus Sales

Representative before changing the transmit channel. Changing the transmit channel

may be a violation of your FCC license and may cause the system to not operate

properly.

•

Utility Code

: Allows you to select your assigned utility code. This value is used when

loading a vehicle route and then applied in AutoVu when the same route is retrieved. The

default value for Utility Code is blank. If you are using a VGB to read FlexNet SmartPoint

modules, you will need to select your assigned utility code before loading your routes.

Vehicle Reading Display Tab

The

Reading Display

tab refers to the display on the Vehicle Read laptop that the Meter

Readers use to read meters. Depending on the settings here, the screen in the AutoVu

program on the laptop will display the multiplier and/or units of measurement information

(if any) and/or change the way the reading appears to the meter reader as the readings

are collected. These settings are only relevant if the billing software passes multiplier or

units of measurement information to AutoRead in the route file, or if these values have been

programmed directly into the register.

Note

3 Polling Devices | 43

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды