Xylem sensus AutoRead Скачать руководство пользователя

Страница: 34 / 161

selections have been made. If not checked, programming begins immediately after the

selections have been made.

•

Load FlexRead Firmware Update

: Loads the FlexNet SmartPoint M2 firmware to the

HHD when a FlexRead route is loaded. The M2 SmartPoints are field-upgradeable and

can be updated (if necessary) using the FlexPro application.

Note

It is strongly recommended to contact Sensus Technical Services before attempting to

update any SmartPoints.

•

Install Fallback Mode Only

: Instructs the FlexPro application to use the fallback mode

contained in the profile when programming SmartPoints. Normally, the fallback mode is

only used when the SNR (Signal-to-Noise Ratio) requirement for the primary mode is not

met.

•

SmartPoints Available

: Instructs the FlexPro application to attempt SmartPoint

programming in one-way mode. One-way SmartPoint transmitters include the

510X/520X (water) as well as the 100G-FL through 700G-FL (gas).

•

SmartPoints M2 Available

: Instructs the FlexPro application to attempt SmartPoint

programming in two-way mode. Two-way SmartPoint transmitters include the

510M/520M and 510P/520P (water). If checked and the

SmartPoint Available

checkbox is checked, then programming will first be attempted in two-way mode. If/

when that is unsuccessful, programming will then be attempted in one-way mode.

•

Initial Gas

Tab: Allows the user to select which Gas Programmer option displays

initially between Metering (NA2W Gas) or Shutoff (RGS) screens upon opening the Gas

Programmer menu in FlexPro.

Gas-Specific Parameters

The following parameters are the default settings that, if unchanged, are programmed into

the SmartPoint. They can be changed on the HHD (if necessary).

•

Meter Type

: Indicates the type of meter that is connected to the SmartPoint. Choices

include Remote Mount (for the 700G-FL series SmartPoint) and Direct Mount.

•

Number of Index Dials

: Sets the number of index dials on the meter connected to the

SmartPoint. Valid values are 2-8 Dials.

3 Polling Devices | 34

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды