Xylem sensus AutoRead Скачать руководство пользователя страница 27

Страница: 27 / 161

•

AUTO-NEXT at Startup

: If this setting is set to On, the HHD will advance to the next

meter automatically when a reading is stored. If this control is set to Off, the meter

reader will need to advance the HHD to the next meter manually after entering a reading.

Entering a note will not advance the HHD to the next meter automatically, regardless of

this setting.

•

Beeper Volume Control

: Sets the default volume of the beeper sound on the HHD. (Not

supported on the AR5000 model HHDs.)

•

Key Click Volume Control

: Determines the default key click volume that the HHD

makes when a key is pressed. (Not supported on the AR5000 model HHDs.)

•

Battery Check

: Dictates whether or not the HHD will warn the meter reader of a low

battery condition. (Not supported on the AR5000 model HHDs.)

•

Times to retry when bad reading is received

: May be used if directed by Sensus

Technical Services to improve MXU response in situations where RadioRead success

is intermittent. Allows the HHD to attempt interrogation multiple times prior to signaling

the Bad Read message. Altering this value without consent from Technical Services may

actually hinder system performance.

The AR400X Tab

The

AR400X

tab is provided to make changes to the default configuration of the AR4001

and AR4002 HHDs. There are settings that are specific to these models that do not apply to

the model 5000 HHDs.
•

Backlight on Time

: This controls the default amount of time that the HHD backlight will

remain on when the

Light

key is pressed on the HHD. A shorter time will help conserve

battery power on the HHD if a meter reader forgets to turn the light off manually. The

setting is displayed in seconds.

3 Polling Devices | 27

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды