Xylem sensus AutoRead Скачать руководство пользователя страница 35

Страница: 35 / 161

•

Meter Units

: Indicates the meter's units of measure. Valid values are Gallons, Liters,

Cubic Feet, and Cubic Meters.

•

Index Reading Resolution

: Will be one of the following valid values: 1x, 10x, 100x, and

1000x.

•

Index Drive

: Will be one of the following valid values: 1, 2, 5, 10, 20, 25, 50, 100, 250,

500, and 1000.

•

Index Scale

: Will be one of the following valid values: CCF, MCF, M3.

•

Initial Reading Resolution

: This is used as the initial reading resolution on the initial

reading screen in FlexPro. During programming, the initial reading is multiplied by this

value before it is stored in the SmartPoint. Will be one of the following valid values: CF,

10CF, CCF, MCF, M3. This is normally the same as the Index Scale.

•

Pulse Per Revolution

: Will be one of the following valid values: 1, 2, 5, 10, 20, 50,

100, 500, and 1000. This parameter is only used when the Meter Type is set to Remote

Mount; otherwise, it is ignored.

•

Compensation Factor

: A value between 0-4 (including decimal values.)

•

Meter Manufacturer

: Indicates the type of meter connected which in turn will dictate

the direction (counter-clockwise or clockwise) that the index drive will turn. Valid

values are AutoDetect, Sensus, Invensys, Rockwell, Equimeter, American, Actaris,

Schlumberger, Sprague, National, Lancaster, Elster, Other: Clockwise Rotation, Other:

Counterclockwise Rot. AutoDetect is the preferred option. If AutoDetect is selected for

this option, the Gas Smartpoint will allow 5 reading revolutions of the index drive to occur

before establishing the direction. For NA2W Gas devices only.

•

Reverse Flow Threshold

: Will be one of the following valid values: Disabled, 1 Count, 2

Counts, 5 Counts, 10 Counts, or 100 Counts. For NA2W Gas devices only.

•

Broken Pipe Threshold

: A value between 0.0 and 4.0. If set to 0.0 then the feature is

disabled. For NA2W Gas devices only.

•

Broken Pipe Time

: Will be one of the following valid values: 0 seconds, 5 seconds, 10

seconds, 15 seconds, 30 seconds, 60 seconds. For NA2W Gas devices only.

Water-Specific Parameters

Water SmartPoints can have two physical ports. Therefore, AutoRead/FlexPro will refer to

Meter A as the first physical port on the SmartPoint and Meter B as the second physical

port. If the Water SmartPoint only has a single physical port, then only Meter A Parameters

are used.

Note

The following parameters are the default settings that, if unchanged, are programmed into

the SmartPoint. They can be changed on the HHD (if necessary).

3 Polling Devices | 35

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды