manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации

Поделиться
Скачать
Viavi 113956 Скачать руководство пользователя страница 68

Operation, 

Screen Layout and Navigation

 

1-2-3

RGS-2000NG TCAS Test Set Operation Manual

139187 / Rev. 500

Page 32

Subject to Export Control. See Cover Page for details.

September 2021

3.4.18

TCAS TRANSMITTER RTCA/DO-260 TESTS SCREEN

TCAS RTCA/DO-260 is currently in development and planned for a future release.

3.4.19

TCAS BLOCK TRANSMISSION SCREEN

The Block Transmission Screen allows the user to set a block of 1090/1030 messages (UF, DF, ATCRBS 

Interrogation and ATCRBS Replies) to transmit at a specific time and block period.

SCREEN SEQUE NCE:

TCAS Block Transmission Screen > Block Transmission Softkey

   

   

F i g u r e   1. 2 . 3   -   3 2   T C A S  B l o c k   T r a n s m i s s i o n   S c re e n /M e n u s

Screen  Components

Description

Load Softkey

Loads a Block Transmission sequence from an internal data location 

or external drive.

Save Softkey

Saves a Block Transmission sequence to the internal data location 

or external drive.

Add Message Softkey

Accesses the Add Message Screen. Refer to Section 

3.4.19.1,  TCAS 

Block Transmission Add Message Screen

.

Message Details Softkey

Accesses the Message Details Screen. Refer to Section 

3.4.19.3, 

TCAS Block Transmission Message Details Softkey Menu

.

Remove Softkey

Removes the selected message from the block sequence.

Reset Softkey

Clears the entire block sequence.

Transmission Toggle Switch

Allows the user to Start or Stop the block transmissions.

Block Period Field

Selects the Block Period.

Mode Toggle Switch

Selects the Mode.

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды