Viavi 113956 Скачать руководство пользователя страница 124

Страница: 124 / 569

Operation,

Screen Layout and Navigation

1-2-3

RGS-2000NG TCAS Test Set Operation Manual

139187 / Rev. 500

Page 88

Subject to Export Control. See Cover Page for details.

September 2021

Tx Channel Menu

Selects the Tx Channel. Tx Channels are defined on the TCAS

Settings user Screen. Refer to Section

3.4.1, TCAS Settings

Screen

Altitude Field

Defines the Altitude.

Bearing (Phase) Field

Defines the Bearing (Phase).

Range Field

Defines the Range.

Latitude Field

Defines the Latitude.

Longitude Field

Defines the Longitude.

Vertical Speed Field

Defines the Vertical Speed.

Velocity Field

Defines the Velocity (Squitter).

Track Field

Defines the Track Angle.

Squitter Power Field

Defines the Squitter Power.

Squitter Antenna Menu

Selects the Squitter Antenna.

Starting at Field

Defines the start time.

Stopping at Field

Defines the stop time.

DO-260 Mode Menu

Selects the DO-260 Mode.

Mode S Address Field

Defines the Mode S Address (Hexadecimal).

Enable

Enables/disables transmitting the required messages for this

intruder.

Altitude Report

Enables/disables the Altitude Report.
If enabled, the altitude code is present in the DF0 reply.
If disabled, the altitude code is set to 0.

Squitter

Enables/disables the Squitter.

Ground

Enables/disables setting the intruder on the ground.

Altitude Code Mode Toggle Switch

Selects the Altitude Code Mode.

Probability Pattern

Squitter Field

Defines the Squitter Probability Pattern.

Reply Field

Defines the Reply Probability Pattern.

Mode A Code Fields

Defines the Mode A Code.

Identification Field

Defines the Intruder Identification.

Type Field

Defines the Intruder Identification Type.

Velocity Type Menu

Selects the Velocity Type.

CF Field

Defines the Transponder Capability.

FS Field

Defines the Flight Status.

Screen Components

Descriptio n

Содержание 113956


























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 113956

Отзывы:

Бренды по названию

Популярные бренды

Viavi 113956, Руководство по эксплуатации

Результаты поиска

Содержание 113956

Отзывы:

Бренды по названию

Популярные бренды