Viavi 113956 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 569

Viavi 113956 Скачать руководство пользователя страница 23

Chapter 1 - Description

General Description and Capabilities

139187 / Rev. 500

RGS-2000NG TCAS Test Set Operation Manual

1-1-1

September 2021

Subject to Export Control. See Cover Page for details.

Page 1

Chapter 1 - Description

1.

GENERAL DESCRIPTION AND CAPABILITIES

1.1

DESCRIPTION

The RGS-2000NG TCAS Test Set is an RF Signal Generator/Receiver for testing TCAS (Traffic Alert and
Collision Avoidance System) with an option available for testing Transponder LRUs.

1.2

FUNCTIONAL CAPABILITIES

The RGS-2000NG has the following features and capabilities:

•

10.4 inch touch screen LCD display for operator control of all test set capabilities or can be
remotely controlled via GPIB or Ethernet

•

Legacy command sets supported:
•

RGS-2000

•

Support for current standards:
•

ADS-B, DO-260, DO-260A, DO-260B

•

UAT, DO-282B (Optional)

•

TCAS, DO-185A, DO-185B

•

TCAS II Hybrid Surveillance, DO-300

•

ATRCRBS/Mode S, DO-181E (Optional)

•

Simulates 32 dynamic / 568 static intruders

•

Transponder test capability for Modes 3/A, C and S (Optional)

•

ADS-B squitter encode/decode

•

Four port antenna simulation

•

Contains six transmitters

•

Enhanced measurement capabilities

•

TX/RX data logging capability

•

Capable of performing most MOPS tests for DO-185A, DO-185B, DO-260, DO-260A, DO-260B,
DO-181E and DO-300 (with appropriate Options).

•

UAT, DO-282B (Optional)

«
...
21
22
23
24
25
...
»

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды