Viavi 113956 Скачать руководство пользователя

Страница: 263 / 569

Operation,

Operating Procedures and Test Configurations

139187 / Rev. 500

RGS-2000NG TCAS Test Set Operation Manual

1-2-4

September 2021

Subject to Export Control. See Cover Page for details.

Page 17

NOTE:

FOR ALL INTRUDERS, THE LOCATION HAS BEEN ENTERED USING THE RANGE

AND BE ARING OR LATITUDE AND LONGIT UDE. I F THE RANGE AND BEARI NG IS

USED, THE TEST SET CALCULATES THE LATITUDE AND LONGIT UDE OF THE

INTRUDER. IF LATITUDE AND LONGITUDE IS USED, THE TEST SET CALCUL AT ES

THE RANGE AND BEARING FROM THE OWN AIRCRAFT.

STEP

PROCEDURE (CONT)

If adding Mode S Squitters, refer to Section

4.1.16, How to Add Mode S Squitters to an Intruder

To include a coordination message, refer to Section

4.1.17, How to Add Coordinations to an

Intruder

To include a broadcast message, refer to Section

4.1.18, How to Add Broadcasts to an Intruder

If adding DF16 Replies, refer to Section

4.1.19, How to Add DF16 Replies to an Intruder

If adding UFO’s, refer to Section

4.1.20, How to Add UFO’s to an Intruder

If adding Waypoints, refer to Section

4.1.22, How to Add Waypoints to an Intruder

When all the required information has been entered, press the

R e t u r n

Softkey to return to the

TCAS Scenario Screen.

To start the scenario, use the

S c e n a r i o

Softkey. Once the scenario has started, the

R u n T i m e

Field on the top of the Scenario Screen changes with the current scenario time.

If the scenario terminates, the

S c e n a r i o

Softkey returns to the OFF position. To terminate the

scenario before the total scenario time, change the

S c e n a r i o

Softkey to the OFF position.

Reply Probability

0, 0.2, 0.4, 0.6, 0.8 or 1

Squitter Probability

0, 0.2, 0.4, 0.6, 0.8 or 1

Mode A Code

0000

0000 to 7777 (Octal)

0 to 7

0 to 31

0 to 63

No TCAS Sensitiv ity Level

0 to 7

RI (AQ= 0)

No on-board TCAS

0 to 7

RI (AQ=1)

No Airspeed

0 to 7

Dynamic Mod e S Extended Minimum Parameters

Parameter

Default

Selectio n (Ran ge)

Содержание 113956


























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 113956

Отзывы:

Похожие инструкции для 113956

Бренды по названию

Популярные бренды

Viavi 113956, Руководство по эксплуатации

Результаты поиска

Содержание 113956

Отзывы:

Похожие инструкции для 113956

Бренды по названию

Популярные бренды