manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации

Поделиться
Скачать
Viavi 113956 Скачать руководство пользователя страница 312

Operation, 

Remote Operation

 

1-2-5

RGS-2000NG TCAS Test Set Operation Manual

139187 / Rev. 500

Page 40

Subject to Export Control. See Cover Page for details.

September 2021

5.8.10.1

Trigger Parameters

5.8.10.2

Mode

5.8.10.3

Source

5.8.10.4

Random Position Width

Command Syntax:

{:RGS | :RGS2000NG}{:DO260}{:TIMING}{:TRIGGER | 

:TRIG}{:MODE}SP<numeric>CR

Description:

This command sets the trigger mode.
Delay+ delays positively all the enabled generators according with each 

delay amount from the trigger source.
Delay- delays all the enable generators negatively.
Random alters the start of all the enable generators from transmission to 

transmission in the range specified.
Walk moves the starting position of the enable generators from the initial 

delay by 50 ns every transmission.

Numeric:

0 to 3

Value

Mode

0

Delay+

1

Delay-

2

Random

3

Walk

Default:

0  (Delay +)

Example:

:RGS:DO260:TIMING:TRIG:MODE 0\r

Command Syntax:

{:RGS | :RGS2000NG}{:DO260}{:TIMING}{:TRIGGER | 

:TRIG}{:SOURCE}SP{GENA | GENB | GENC | GEN D | GENE | GENF}CR

Description:

This command sets the generator trigger source.
In Low Power Mode, all generators are available.
In High Power Mode, only the gen erators GENA, GENC and GENE are 

available

Default:

Gen A

Example:

:RGS:DO260:TIMING:TRIG:SOURCE GENA\r

Command Syntax:

{:RGS | :RGS2000NG}{:DO260}{:TIMING}{:TRIGGER | 

:TRIG}{:RANDOM}{:WIDTH | :WID}SP<numeric>CR

Description:

This command sets the width in ns of the random pulse.

Numeric:

0 to 120000 ns (decimal ASCII).

Default:

120000 ns

Example:

:RGS:DO260:TIMING:TRIG:RANDOM:WID 1200\r

NOTE:

This command is valid only if the trigger mode is Random. 

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды