manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации

Поделиться
Скачать
Viavi 113956 Скачать руководство пользователя страница 362

Operation, 

Remote Operation

 

1-2-5

RGS-2000NG TCAS Test Set Operation Manual

139187 / Rev. 500

Page 90

Subject to Export Control. See Cover Page for details.

September 2021

5.9.4.20.7

At Time

5.9.4.21

Reply Parameters

5.9.4.21.1

Antenna

5.9.4.21.2

Enable

5.9.4.21.3

Power

Command Syntax:

{:RGS | :RGS2000NG}{:SCE | :SCENARIO}{:DYN: | :DYNAMIC:}<intruder 

number>{:WAY | :WAYPOINTS}{:POS: | :POSITION:}<position 

number>{:BEGIN}SP<numeric>CR

Description:

This command sets the time at the selected waypoint for the selected 

intruder.

Numeric:

0 to 6550 seconds (decimal ASCII)

Default:

Intruder Start Time

Example:

:RGS:SCE:DYN:1:WAY:POS:2:BEGIN 45\r

Command Syntax:

{:RGS | :RGS2000NG}{:SCE | :SCENARIO}{:STAT: | :STATIC: | :DYN: | 

:DYNAMIC:}<intruder number>{:RPLYANT}SP{TOP | BOTTOM | BOTH | 

ALTERNATE | ALTITUDE}CR

Description:

This command sets the reply antenna for the intruder. The interrogation 

must match the reply antenna for an intruder to respond to an i nterrogation. 

If Alternate is selected, then the reply antenna is changed every second. 

This command is not used for ATCRBS intruders.

Default:

By Altitude

Example:

:RGS:SCE:DYN:1:RPLYANT BOTH\r

Command Syntax:

{:RGS | :RGS2000NG}{:SCE | :SCENARIO}{:STAT: | :STATIC: | :DYN: | 

:DYNAMIC:}<intruder number>{:REPLY}SP{ON | OFF}CR

Description:

This command either enables or disables replies for the specified intruder.

Default:

On

Example:

:RGS:SCE:DYN:1:REPLY ON\r

Command Syntax:

{:RGS | :RGS2000NG}{:SCE | :SCENARIO}{:STAT: | :STATIC: | :DYN: | 

:DYNAMIC:}<intruder number>{:RPLYPWR}SP<numeric>CR

Description:

This command sets the power level of the reply message.

Numeric:

High Power Mode: 1 to -69 dBm (decimal ASCII)
Low Power Mode: -20 to - 90 dBm (decimal ASCII)

Default:

-50 dBm

Example:

:RGS:SCE:DYN:1:RPLYPWR -40\r

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды