manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации


Поделиться
Скачать
background image

Chapter 2 - Operation

Installation

 

139187 / Rev. 500

RGS-2000NG TCAS Test Set Operation Manual

1-2-1

September 2021

Subject to Export Control. See Cover Page for details.

Page 6

1.6.3

TROUBLESHOOTING VNC CONNECTION

1.6.3.1

Verify Network Connections

•

Verify the Host Controller (i.e., computer, tablet, Smartphone) and Test Set are connected to the 
same LAN.

•

Verify the correct LAN IP Address has been entered into the TightVNC Connection Window. For 
example, the IP Address for the active LAN Connection and not an internal Test Set IP.

1.6.3.2

Tight VNC Password Error

The following error message indicates the Test Set’s VNC Password was not valid:

Figure 1.2.1 - 5  Tight VNC Authentication Error (Password Error)

Possible Cause of Error:

•

Password was entered incorrectly (i.e., Caps Lock was on).

•

Correct password was entered  (i.e., Default Password may have been changed).

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 113956

Campbell SkyVUE 8M Quick Deploy Manual preview
SkyVUE 8M
Бренд: Campbell Страницы: 2
Daktronics Sportsound SSR-300 Operation Manual preview
Sportsound SSR-300
Бренд: Daktronics Страницы: 42
Gainsborough K223 Quick Manual preview
K223
Бренд: Gainsborough Страницы: 2
Gainsborough H590 Instructions For Use preview
H590
Бренд: Gainsborough Страницы: 2
Gait up GAIT UP GO Quick Start Manual preview
GAIT UP GO
Бренд: Gait up Страницы: 12
Gait up Physilog 6S Quick Start Manual preview
Physilog 6S
Бренд: Gait up Страницы: 6
Gaiam Stability Ball Setup, Workout Tips And Care & Safety Manual preview
Stability Ball
Бренд: Gaiam Страницы: 2
Balanced Body Konnector Installing preview
Konnector
Бренд: Balanced Body Страницы: 4
Balanced Body Arm Chair Assembling preview
Arm Chair
Бренд: Balanced Body Страницы: 2
Balanced Body Reformer Trapeze Combination Manual preview
Reformer Trapeze Combination
Бренд: Balanced Body Страницы: 164
Wacker Neuson VP Operator'S Manual preview
VP
Бренд: Wacker Neuson Страницы: 50
Balanced Body CoreAlign Assembly And Use preview
CoreAlign
Бренд: Balanced Body Страницы: 37
Fast RH15 Owner'S Manual preview
RH15
Бренд: Fast Страницы: 60
Keithley 1973 Instruction Manual preview
1973
Бренд: Keithley Страницы: 57
ABB HT588579 Operation Manual preview
HT588579
Бренд: ABB Страницы: 136
ABB HT598319 Operation Manual preview
HT598319
Бренд: ABB Страницы: 108
Beckman Coulter Optima LE-80K Instruction Manual preview
Optima LE-80K
Бренд: Beckman Coulter Страницы: 52
Copernicus Royal RC005 Assembly Manual preview
Royal RC005
Бренд: Copernicus Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды