manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации


Поделиться
Скачать
background image

Appendix D - SDX Compatibility Command Set Table

 

139187 / Rev. 500

RGS-2000NG TCAS Test Set Operation Manual

Appendix - 

D

September 2021

Subject to Export Control. See Cover Page for details.

Page 1

Appendix D - SDX Compatibility Command Set Table

SDX COMMAND

SUPPORTED / NOT SUPPORTED

COMMENTS

RGS-2000NG EQUIVALENT (OR SIMILAR)

INSTRUMENT COMMANDS

:INSTrument ATCRBS

Supported

:RGS2000:SCENARIO:TYPE XPDR

:RGS2000:XPDR:TYPE 0

:RGS2000:XPDR:MODE

:INSTrument MODES

Supported

:RGS2000:SCENARIO:TYPE XPDR

:RGS2000:XPDR:TYPE 2

:INSTrument DATALINK 

Not Supported

Datalink is a legacy transponder mode which is not support 

by the ATC-5000NG.

None

:INSTrument DATALINK2

Not Supported

Datalink is a legacy transponder mode which is not support 

by the ATC-5000NG.

None

:INSTrument?

Supported

:RGS2000:XPDR:MODE?

:INSTrument:SAVE

Supported

:RGS2000:XPDR:SAVE

:INSTrument:RESTore

Supported

:RGS2000:XPDR:LOAD

:INSTrument:CABLOS

Supported

:RGS2000:XPDR:CABLOS

:INSTrument:CABLOS?

Supported

None

:INSTrument:CABLOSBOT

Supported

:RGS2000:XPDR:CABLOSBOT

:INSTrument:CABLOSBOT?

Supported

None

:INSTrument:FORMAT

Supported

None

:INSTrument:FORMAT?

Supported

None

:INSTrument:COMTEST?

Not Supported

The SDX-2000 specific command COMTEST? directs the test 

set to report software versions and status. The comparable 

ATC-5000NG command is ATC5000NG:ATC:SW?

None

:INSTrument:STATE

Supported

:RGS2000:ACCESS

ATCRBS COMMANDS

:ATCRBS:MODE

Supported

Mode A, C, and AC.

:RGS2000:XPDR:MODE

:ATCRBS:MODE?

Supported

:RGS2000:XPDR:MODE?

:ATCRBS:DOUBle

Supported

:RGS2000:XPDR:TYPE 1

:ATCRBS:DOUBle:SPACing

Supported

:RGS2000:XPDR:DBL:P1TOP1

:ATCRBS:DOUBle?

Supported

None

:ATCRBS:SUBmode

Supported

Multiple Commands for each submode

:ATCRBS:SUBmode?

Supported

None

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 113956

ABB ACS880-01 Series Installation Manual preview
ACS880-01 Series
Бренд: ABB Страницы: 238
NARGESA H1 Instruction Book preview
H1
Бренд: NARGESA Страницы: 33
Raymarine ST7000 Installation Instructions Manual preview
ST7000
Бренд: Raymarine Страницы: 55
Halyard MIC Series Instructions For Use preview
MIC Series
Бренд: Halyard Страницы: 4
GAME Underwater Light Show & Fountain Instructions preview
Underwater Light Show & Fountain
Бренд: GAME Страницы: 2
Raytech TR-1 Instruction Manual preview
TR-1
Бренд: Raytech Страницы: 21
Teac LX Series Specifications preview
LX Series
Бренд: Teac Страницы: 2
laerdal HEARTSTART Quick Start Manual preview
HEARTSTART
Бренд: laerdal Страницы: 2
Yamaha A3000 Upgrade Manual preview
A3000
Бренд: Yamaha Страницы: 50
A&D PT Series Instruction Manual preview
PT Series
Бренд: A&D Страницы: 30
Haigh Quattro Operating & Maintenance Manual preview
Quattro
Бренд: Haigh Страницы: 60
Farmet FALCON PRO Operating Instruction preview
FALCON PRO
Бренд: Farmet Страницы: 102
Yamaha QX1 Owner'S Manual preview
QX1
Бренд: Yamaha Страницы: 46
Laserworld EL-60 G Manual preview
EL-60 G
Бренд: Laserworld Страницы: 8
Laserworld EL 200 LED User Manual preview
EL 200 LED
Бренд: Laserworld Страницы: 6
LaserLiner ActivePen Manual preview
ActivePen
Бренд: LaserLiner Страницы: 56
LaserLiner AC-tiveMaster Operating Instructions Manual preview
AC-tiveMaster
Бренд: LaserLiner Страницы: 54
RainPoint ITV105 User Manual preview
ITV105
Бренд: RainPoint Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды