Viavi 113956 Скачать руководство пользователя страница 434

Страница: 434 / 569

Operation,

Remote Operation

1-2-5

RGS-2000NG TCAS Test Set Operation Manual

139187 / Rev. 500

Page 162

Subject to Export Control. See Cover Page for details.

September 2021

5.11.7

INTERROGATION TOP ANTENNA POWER

5.11.8

LOAD TEST

5.11.9

RESET

5.11.10

SAVE TEST

5.11.11

SCOPE TRIGGER

Command Syntax:

{:RGS | :RGS2000NG}{:XPDR}{:POW | :POWER}SP<numeric>CR

Description:

This command sets the antenna power for the top antenna. The bottom

antenna power uses this value pl us the antenna power deviation setting.

Numeric:

-20 to -90 dBm (decimal ASCII)

Default:

-20 dBm

Example:

:RGS:XPDR:POW -21\r

Query:

:RGS:XPDR:POW?\r

Returns:

-21

Command Syntax:

{:RGS | :RGS2000NG}{:XPDR}{:LOAD}SP<filename>CR

Description:

This command loads a CSV test file (specified filename) from the internal

storage area.

Return:

”*” is returned if the command was able to complete successfully.
“?” is returned if a failure occurs.

Example:

:RGS:XPDR:LOAD Xpdr1.csv\r

NOTE:

Must have previously saved a test under file name to be loaded.

Command Syntax:

{:RGS | :RGS2000NG}{:XPDR}{:RES | :RESET}CR

Description:

This command resets the transponder test.

Example:

:RGS:XPDR:RES\r

Command Syntax:

{:RGS | :RGS2000NG}{:XPDR}{:SAVE}SP<filename>CR

Description:

This command saves the current test into the internal storage area with the

specified filename.

Example:

:RGS:XPDR:SAVE Xpdr1.csv\r

Command Syntax:

{:RGS | :RGS2000NG}{:XPDR:SCOPE}SP{INTERR | REPLY}CR

Description:

This command sets the scope trigger either to the interrogation or the reply.

Default:

Interrogation

Example:

:RGS:XPDR:SCOPE REPLY\r

Query:

:RGS:XPDR:SCOPE?\r

Returns:

Содержание 113956


























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 113956

Отзывы:

Бренды по названию

Популярные бренды

Viavi 113956, Руководство по эксплуатации

Результаты поиска

Содержание 113956

Отзывы:

Бренды по названию

Популярные бренды