manualshive.com logo in svg

Viavi 113956, Руководство по эксплуатации


Поделиться
Скачать
background image

Specifications, Chapter 3 - Specifications

Interrogation specifications (XPDR)

, Interrogation table/burst mode

1-3-1

RGS-2000NG TCAS Test Set Operation Manual

139187 / Rev. 500

Page 10

Subject to Export Control. See Cover Page for details.

September 2021

2.1.5

VERTICAL SPEED (TCAS)

Range:

32,608 ft /min

Resolution:

64 ft /min

Accuracy:

64 ft /min

2.1.6

ALTITUDE SIMULATION (TCAS)

Range:

-1000 to +126700 ft

Resolution:

50175 ft altitude:

25 or 100 ft

>50175 ft altitude:

100 ft

Accuracy:

25 ft

3.

INTERROGATION SPECIFICATIONS (XPDR)

3.1

INTERROGATION TABLE/BURST MODE

Number of Messages:

1 to 1000

Interrogations/Burst

1 to 10,000

Burst Spacing:

Range:

0 to 20 s (0 s for single-burst transmission)

Resolution:

0.1 s

Accuracy

100 ms

Burst/Trigger:

1, continuous until Stop command received

3.2

BLOCK TRANSMISSIONS MODE

Number of Messages:

TCAS:

1 to 1000

XPDR:

1 to 2000

Number of Blocks: 

1 to 50000 or infinite

Message Spacing within Block:

Range: 

10 to 99880 

s (maximum spacing limited to the 

block period minus 120 

s)

Resolution: 

1.0 

s

Block Period:

Range: 

10 ms to 90 sec

Resolution: 

1 ms

Accuracy: 

1 ms

3.3

PRF (INTERROGATIONS, XPDR)

Single Interrogation:

Range: 

1 Hz to 10 KHz

Resolution: 

1 Hz

Accuracy: 

0.1% of setting

Содержание 113956


























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 113956

Napoleon S1 Assembly Replacement Instructions preview
S1
Бренд: Napoleon Страницы: 2
Raytheon V800 Instruction Manual preview
V800
Бренд: Raytheon Страницы: 62
Zetec TOPAZ Technical Manuallines preview
TOPAZ
Бренд: Zetec Страницы: 23
B&G H5000 Pilot Calibration Manual preview
H5000 Pilot
Бренд: B&G Страницы: 3
NANLUX TK-200 Manual preview
TK-200
Бренд: NANLUX Страницы: 39
Konica Minolta DF-619 Service Manual preview
DF-619
Бренд: Konica Minolta Страницы: 32
Yamaha TG300 Sound List & Midi Data preview
TG300
Бренд: Yamaha Страницы: 39
Yamaha MU100 Supplementary Manual preview
MU100
Бренд: Yamaha Страницы: 110
Agilent Technologies Intuvo 9000 Installation And First Startup preview
Intuvo 9000
Бренд: Agilent Technologies Страницы: 114
PFM Medical Slide 4004 M Operating Manual preview
Slide 4004 M
Бренд: PFM Medical Страницы: 26
gorilla sports GYRONETICS E-Series Manual preview
GYRONETICS E-Series
Бренд: gorilla sports Страницы: 22
Wiedenmann 497.001 Translation Of Original Operating Instructions preview
497.001
Бренд: Wiedenmann Страницы: 41
Campbell Advisor Guide Pedestrian Signal User Manual preview
Advisor Guide Pedestrian Signal
Бренд: Campbell Страницы: 14
Handicare 201903314 User Manual preview
201903314
Бренд: Handicare Страницы: 18
Nakamichi NDS6831 User Manual preview
NDS6831
Бренд: Nakamichi Страницы: 12
Norwest Pivot track filler Owner'S Manual preview
Pivot track filler
Бренд: Norwest Страницы: 16
ResMed AirSense 11 Manual preview
AirSense 11
Бренд: ResMed Страницы: 9
Festo CPX-AP-A Operating Instructions Manual preview
CPX-AP-A
Бренд: Festo Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды