manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

SERVICING AND HANDLING

WARNING:
Many of service procedures require disconnection of
“AIR BAG” fuse and all air bag (inflator) module(s) from
initiator circuit to avoid an accidental deployment.
Driver and Passenger Air Bag (Inflator) Modules

For handling and storage of a live air bag (inflator)
module, select a place where the ambient temperature
below 65

C (150

F), without high humidity and away

from electric noise.

When carrying a live air bag (inflator) module, make
sure the bag opening is pointed away from you. In case
of an accidental deployment, the bag will then deploy
with minimal chance of injury. Never carry the air bag
(inflator) module by the wires or connector on the un-
derside of the module. When placing a live air bag (in-
flator) module on a bench or other surface, always face
the bag up, away from the surface. As the live passen-
ger air bag (inflator) module must be placed with its
bag (trim cover) facing up, place it on the workbench
with a slit (1) or use the workbench vise (2) to hold it
securely at its lower mounting bracket (3). This is nec-
essary so that a free space is provided to allow the air
bag to expand in the unlikely event of accidental de-
ployment. Otherwise, personal injury may result.

Never dispose of live (undeployed) air bag (inflator)
modules (driver and passenger). If disposal is neces-
sary, be sure to deploy them according to deployment
procedures described in SECTION 10B before dispos-
al.

The air bag (inflator) module immediately after deploy-
ment is very hot. Wait for at least half an hour to cool
it off before proceeding the work.

After an air bag (inflator) module has been deployed,
the surface of the air bag may contain a powdery resi-
due. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and by-prod-
ucts of the chemical reaction. As with many service
procedures, gloves and safety glasses should be
worn.

ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.

ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.

1

3

2

0A-4

GENGERAL INFORMATION

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
FORM FIT 1303 Installation Instructions preview
1303
Бренд: FORM FIT Страницы: 2
Renault ALASKAN 2017 Driver'S Handbook Manual preview
ALASKAN 2017
Бренд: Renault Страницы: 340
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Бренд: Gator Страницы: 8
benbat BM721 Instructions For Use Manual preview
BM721
Бренд: benbat Страницы: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Бренд: SPL Страницы: 5
Audi Audi 80 1987 Workshop Manual preview
Audi 80 1987
Бренд: Audi Страницы: 63
Whispbar K835W Fitting Instructions For Basic Carrier preview
K835W
Бренд: Whispbar Страницы: 63
Saab 2000 9-5 2.3 Turbo Ecopower Owner'S Manual preview
2000 9-5 2.3 Turbo Ecopower
Бренд: Saab Страницы: 256
Ford Escape 2022 Owner'S Manual preview
Escape 2022
Бренд: Ford Страницы: 585
Whispbar K684W Fitting Instructions Manual preview
K684W
Бренд: Whispbar Страницы: 15
GMC 2008 Savana Van Owner'S Manual preview
2008 Savana Van
Бренд: GMC Страницы: 402
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Бренд: Acura Страницы: 16
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Бренд: Edelbrock Страницы: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Бренд: GMC Страницы: 439
MiX Telematics FM 3617i Installation Manual preview
FM 3617i
Бренд: MiX Telematics Страницы: 39
Pyle PLPSC8 User Manual preview
PLPSC8
Бренд: Pyle Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды