manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

ON-VEHICLE SERVICE

OIL CHANGE

1) Before changing or inspecting oil, be sure to stop engine and lift

vehicle horizontally.

2) With vehicle lifted up, check oil level and leakage.

If leakage exists, correct it.

3) Drain old oil and fill new specified oil by specified amount (up to

level hole).

4) Apply sealant to thread of drain plug (1) and level/filler plug (2).

Torque drain and level/filler plugs as specified below.

“A”: Sealant 99000-31110

Tightening Torque
(a): 21 N·m (2.1 kg-m, 15.5 lb-ft)

NOTE:

It is recommended to use API GL-4 75W-90 gear oil.

Whenever vehicle is hoisted for any other service work
than oil change, also be sure to check for oil leakage.

Oil specification: API GL-4

For SAE classification, refer to viscosity
chart at the left.

Oil capacity: 2.7 liters (5.7/4.8 US/lmp. pt)

Viscosity chart
SAE

2, (a), “A”

1, (a), “A”

Temperature

[Right side]

[Left side]

7A-6

MANUAL TRANSMISSION

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

AA Products KX405 Instruction Manual preview
KX405
Бренд: AA Products Страницы: 8
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Бренд: hager Страницы: 9
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Бренд: Farad Страницы: 8
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Бренд: GReddy Страницы: 9
Hummer 2006 H2 Owner'S Manual preview
2006 H2
Бренд: Hummer Страницы: 502
Park-Daddy PD50AA Installation Manual preview
PD50AA
Бренд: Park-Daddy Страницы: 22
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Бренд: STARLANE Страницы: 24
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
Safe Fleet PRIME DESIGN HXR-269-E-UM3-80 Manual preview
PRIME DESIGN HXR-269-E-UM3-80
Бренд: Safe Fleet Страницы: 12
ULTIMATE SPEED 1188 1525 Instructions For Use And Safety Manuallines preview
1188 1525
Бренд: ULTIMATE SPEED Страницы: 26
Saab 32 025 687 Installation Instructions Manual preview
32 025 687
Бренд: Saab Страницы: 9
L.A. West Sprinter Shuttle Owner'S Manual preview
Sprinter Shuttle
Бренд: L.A. West Страницы: 30
Navman F-Series B2+ User Manual preview
F-Series B2+
Бренд: Navman Страницы: 10
Cruiser Consoles BUSHMAN 15L ROADIE fridge Base console Installation Instructions Manual preview
BUSHMAN 15L ROADIE fridge Base console
Бренд: Cruiser Consoles Страницы: 6
Metra Electronics 99-7400 Installation Instructions Manual preview
99-7400
Бренд: Metra Electronics Страницы: 8
Macally HRMOUNTPROTRAY User Manual preview
HRMOUNTPROTRAY
Бренд: Macally Страницы: 19
TAUBENREUTHER 2360-00 Manual preview
2360-00
Бренд: TAUBENREUTHER Страницы: 10
Sony Ericsson HCA-60 User Manual preview
HCA-60
Бренд: Sony Ericsson Страницы: 116

Бренды по названию

Популярные бренды

Загрузить еще бренды